Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Currently selected item 6 6cm 1 1... CAS I O COMPUTE COMPANY R AB B Use c, v, x and z to move the underlining left, right, up and down and change the selected item. B Press SET to execute the underlined item, or ESC to exit the displayed menu (and return to the previous menu or screen) without selecting anything. B When you press SET to execute a menu item, the Label Printer either moves on to the next menu, or it executes the selected function and returns to the text input screen that you started from. If the cassette cover detaches Reattach the cover as shown in the illustration. Take care to avoid excessive bending of the cover, which creates the risk of damage to the tabs and holes. Pa rt 2 Pa rt 2 Getting Read y This part of the manual tells you how to load batteries and the tape cartridge, and how to perform other basic setups for the Label Printer. Impor tant! . Be sure to read this section before attempting to use the Label Printer. Po wer Suppl y The Label Printer can be powered by six AA-size alkaline batteries or an optional AC adaptor (AD-A95100). Replacing Batteries A handy low battery power indicator lets you know when battery power is getting too low for proper operation. The message “LOW BATTERY!” appears on the display if battery power is low when you perform any of the following operations. . Turn power on . Execute a print operation Whenever the “LOW BATTERY! SET/ESC” message appears, press SET to clear it from the display. You should still be able to perform some Label Printer operations, but some power intensive operations (like printing) may become impossible if battery power is too low. In any case, you should replace batteries as soon as possible after the “LOW BATTERY!” message appears. Impor tant! . Batteries can burst or leak and damage your unit if you do not use them correctly. Note the following important points. . Be sure that the plus (+) and minus (–) sides of each battery are facing correctly. . Never mix batteries of different types. . Never leave dead batteries in the Label Printer. . Remove the batteries if you do not plan to use the Label Printer for a long time. Wa r n ing! . Never use recharged batteries with the unit. B Do not expose batteries to direct heat, do not short circuit them, and do not try to take them apart. B Keep batteries out of the reach of small children. If swallowed, consult with a physician immediately. Memory Data Backup B Never remove the batteries or disconnect the AC adaptor (page E-9) while the printer is turned on. Also, make sure that the display is completely blank after turning off the printer before removing the batteries or disconnecting the AC adaptor. Removing the batteries or disconnecting the AC adaptor at the wrong time can cause loss of text you are working on, as well as data you have stored in printer memory. B Be sure to keep separate backup copies of all important data you have stored in printer memory. Impor tant! B The printer may suddenly turn off during printing if battery power goes low. Because of this, use of the optional AC adaptor (page E-9) is recommended to power the printer. B Whenever switching between battery power and AC adaptor power, be sure to first turn off the printer. Only then should you connect the AC adaptor or load batteries. Connecting the AC adaptor or loading batteries while the printer is on can cause power to turn off automatically, resulting in loss of text you are working on. Batter y Lif e B Printing of approximately four 18mm tape cartridges under standard printing conditions* * When printing text or graphics that contain large areas of black, and printing under cold temperatures can shorten battery life. To load the batteries Caution B Do not touch the springs inside the battery compartment cover with your fingers while loading or replacing batteries. The springs have sharp areas and can cut your fingers. Important! B The Label Printer can run on six AA-size alkaline batteries. Be sure to use alkaline batteries only. 1. Turn power off. B If you are using the optional AC adaptor for power, you should also unplug it from the Label Printer. 2. Turn over the Label Printer. Open the battery compartment cover as shown in the illustration. 3. Load batteries into the battery compartment. . Be sure to use alkaline batteries. . Make sure the positive (+) and negative (–) ends of the batteries are facing in the correct directions. 4. Replace the battery compartment cover. AC Adaptor Note the following important precautions when using an optional AC adaptor to power your Label Printer. . Use only a genuine CASIO AD-A95100 AC adaptor with the same voltage rating as the household current in your area. Using a wrong adaptor can damage your Label Printer. B Be sure to turn the Label Printer off before you connect the adaptor. Do not turn power on until the adaptor is connected to the Label Printer and plugged into and AC outlet. B Be sure to unplug the AC adaptor from the AC outlet whenever you are not usin...