Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Toshiba Dateigröße: 1.23 mb Dateiname: Unterrichtssprache:

4. Close the Strip Block and Top Cover. E2-11 2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media 2.7 Loading the Media (Cont.) WARNING! HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY The cutter is sharp, so care must be taken not to injure yourself when handling the cutter. CAUTION! 1. Be sure to cut the backing paper of the label. Cutting labels will cause the glue to stick to the cutter which may affect the cutter quality and shorten the cutter life. 2. Use of tag paper of which thickness exceeds the specified value may affect the cutter life. NOTE: When placing fanfold paper stock on the rear of the printer, the following care should be taken. 1. Face the print surface up. 2. The fanfold paper stock is parallel to and level with the fanfold paper slot. 3. Interface cables do not interfere with the feed of fanfold paper. Cut mode (Option): When the Cutter is installed, the media is automatically cut. After loading the media as described on the previous pages, insert the leading edge of the media through the Media Outlet of the Cutter Cover. Cutter Cover Media Outlet Fanfold Paper Stock Fanfold Paper Slot How to Load Fanfold Paper Stock 1. Place the fanfold paper stock on the rear of the printer, and insert the leading edge of the paper into the Fanfold Paper Slot. 2. Refer to the previous pages to feed the fanfold paper through the printer until it extends past the media outlet. E2-12 2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media 2.7 Loading the Media When a media roll has an outside diameter exceeding 127 mm (5”) and the inner core diameter of 76.2 mm (3”), the optional External Media Roll (Cont.) Hanger is required. 1. Fit the protrusions on the bottom of the printer into the holes in the External Media Roll Hanger. External Media Roll Hanger (Option) 2. Insert the Media Shaft into the core of the media roll. 3. Place it into the cuts of the External Media Roll Hanger. 4. Pull the media forward and insert the leading edge into the Fanfold Paper Slot. Fanfold Paper Slot Media Shaft (Option) 5. Refer to the previous pages to complete the media loading. 6. Close the Top Cover. E2-13 2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.8 Loading the Ribbon 2.8 Loading the Ribbon When you use normal media, it is necessary to load a ribbon. Follow the procedure below to load a ribbon properly. 1. Press down the Top Cover Release Button to unlock the Top Cover, then fully open the Top Cover. Top Cover Top Cover Release Button WARNING! 1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc. being drawn into the moving parts, be sure to load the media once the printer has stopped moving completely. 2. To avoid injury, be careful not to trap your fingers while opening or closing the cover. CAUTION! Be careful not to touch the Print Head Element when opening the Top Cover. Failure to do this may cause missing dots by static electricity or other print quality problems. NOTES: 1. Do not load a ribbon when using direct thermal media. Doing so may damage the print head or stained with melted ribbon, which requires a replacement of the print head. 2. Be sure to load the ribbon so that the ink side contacts with the print side of the media. If the ribbon is loaded inside out, nothing can be printed, and eventually the print head will need to be replaced. 3. The Figure shows how to distinguish between used and unused sides of a halfway- used ribbon. 4. As the ribbon is very thin, do not pull the ribbon strongly. Doing so may cause the ribbon to be stretched or broken. 2. Fit the core of the Ribbon Supply Roll into both the Spring Guide Wheel and the Guide Wheel (Supply side). (1) Push the right side of the core of the Ribbon Supply Roll against the Spring Guide Wheel and fit the wheel into the core. Ribbon Supply Roll Spring Guide Wheel (Supply side) (2) Fit the left side of the core of the Ribbon Supply Roll to the Guide Wheel, aligning the notch of the ribbon core with the protrusion of the Guide Wheel. Hold the ribbon firmly while loading it, as it is easily loosened or unrolled. E2-14 2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.8 Loading the Ribbon 2.8 Loading the Ribbon (Cont.) NOTE: Ribbon Path Ribbon Take-up Core Ribbon Supply Roll Print Head 3. Push up the Ribbon Access Cover by the portions indicated by arrows A and fully open it supporting the Print Head Block. A Ribbon Access Cover A Print Head Block 4. Fit the Ribbon Take-up Roll to the Spring Guide Wheel and the Guide Wheel in the same way as the Ribbon Supply Roll. (1) Push the right side of the core of the Ribbon Take-up Roll against the Spring Guide Wheel and fit the wheel into the core. (2) Fit the left side of the core of the Ribbon Take-up Core to the Guide Wheel, aligning the notch of the ribbon core with the protrusion of the Guide Wheel. Spring Guide Wheel (Take-up side) Guide Wheel 5. Turn the Ribbon Rewind Gear to wind the ribbon leading film onto the Ribbon Take-up Core u...

Herunterladen

Geben Sie zwei Ziffern: