Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Store the monitor in a safe and dry location. Do not subject the monitor to extreme hot or cold temperatures, humidity and direct sunlight. Avoid subjecting the monitor to strong shocks, such as dropping the unit on the floor. Remove the batteries if the unit will not be used for three months or longer. Always replace all the batteries with new ones at the same time. Use the unit consistent with the instruction provided in this manual. Use only authorized parts and accessories. 20 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 20 ERROR INDICATORS SYMBOL CAUSE CORRECTION Monitor did not detect pulse rate Remove the arm cuff. Refer to “Applying the arm cuff” on page 13. Wait 2-3 minutes. Take another measurement. Cuff under-inflated Remove the arm cuff. Read, “Taking a Measurement” on page 16. Wait 2-3 minutes. Take another measurement. Cuff over-inflated Batteries are worn Replace worn batteries. Refer to page 8 for battery installation. Movement during measurement Remove the arm cuff. Wait 2-3 minutes. Take another measurement. Remain still during the measurement. 21 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 21 TROUBLESHOOTING TIPS PROBLEM CAUSES AND SOLUTIONS No power. No display appears on the unit. Replace all four batteries. Check the battery installation for proper placement of the battery polarities. Measurement values appear too high or too low. Blood pressure varies constantly. Many factors including stress, time of day, how you wrap the cuff, may affect your blood pressure. Review the sections “Before Taking a Measurement” and “Taking a Measurement”. 22 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 22 QUICK REFERENCE GUIDE To ensure a reliable reading, avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before taking a measurement. You should try to measure your blood pressure at the same time each day. Avoid taking measurements during stressful times. 1. Remove any tight-fitting clothing from your upper arm. 2. Sit in a chair with your feet flat on the floor and place your arm on a table so the cuff is at the same level as your heart. 3. Apply the arm cuff to your left upper arm so the blue strip is on the inside of your arm and aligned with your middle finger. The air tube runs down the inside of your arm. The bottom of the cuff should be approximately 1/2" above your elbow. 1/2 inch (1 - 2 cm) Air Tube Blue Strip 4. Wrap the cuff firmly in place around your arm using the closure strip. 23 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 23 QUICK REFERENCE GUIDE 5. Press the START/STOP button. Display symbols appear. The cuff starts to inflate automatically. Remain still and do not talk during the measurement. NOTE: To stop the inflation or measurement, push the START/STOP button. The monitor will stop inflating, start deflating, and will turn off. 6. When the measurement is complete, the arm cuff completely deflates. Your blood pressure and pulse rate are displayed. NOTE: Wait 2-3 minutes between measurements. The wait time allows the arteries to return to the condition prior to taking the blood pressure measurement. You may need to increase the wait time depending on your individual physiological characteristics. 24 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 24 FCC STATEMENT Note: POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only) This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the product and the receiver. • Connect the product into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Canadian Department of Communications. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 25 780RELN IM Final 8-29-05.qxd 8/29/05 5:24 PM Page 25 WARRANTY INFORMATION LIMITED WARRANTY Your ReliOn® HEM-780...