Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
See Fig. 3. Set base aside. 3 Figure 3 PROG MAN CHANGE SET AUTO/MAN Elec Gas RHAM PM MORN DAY EVE NITE RC W Y G FAN AUTO ON MOUNTING HOLES COOL OFF HEAT 7. Drill the marked holes using a 3/16” drill bit. Note: Enclosed plastic anchors do not require a drilled hole for drywall. 8. Tap plastic anchors into the wall. 9. Align base with plastic anchors and feed wires through opening. See Fig 4. Figure 4 PROG MAN CHANGE SET AUTO/MAN Elec Gas RHAM PM MORN DAY EVE NITE RC W Y G FAN AUTO ONCOOL OFF HEAT 10. Secure base to wall with supplied screws. 11. Connect wires to terminal strip. Refer to wiring diagrams on other side of this sheet. Make sure wire connections are secure. 12. Place fan option switch into either the “ELEC” or “GAS” position depending upon the type of furnace. Refer to Figure 5. Figure 5 4 PROG MAN CHANGE SET AUTO/MAN Elec Gas RHAM PM MORN DAY EVE NITE RC W Y G FAN AUTO ONCOOL OFF HEAT FAN OPTION SWITCH Controls fan delay. 13. Install two “AA” ENERGIZER brand batteries or equivalent into battery compartment. Be sure to match positive (+) ends of batteries with positive (+) battery terminals in the battery compartment. The display will show as follows: 14. Replace cover onto thermostat by snapping into place. 15. Turn on power to system . Test thermostat as described in the following section. Programming Guide Set Time of Day, Day of Week, Temperature Differential 1. Press & Hold SET. Press PROG/MAN Release simultaneously. or PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON >> SET PROG/MAN >> >> 2. Press to change Time of Day. 3. Press 4. Press SET >>1=MO 2=TU 3=WE To Change Day of Week 4=TH 5=FR 6=SA 7=SU 5 5. Press 6. Press >> SET To change Temperature Differential* *The Temperature Differential is Factory preset at 1°. This means that whenever the room temperature changes by one full degree from the temperature setting, the system will turn on. If the system turns on too often, increase the temperature differential. 7. Press SET to finish. Changing Fahrenheit (F) to Celsius (C) Press and Hold SET Press SET > Release both simultaneously. Setting Daily Programming 1. Place COOL-OFF-HEAT switch in COOL position. or PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON >> COOL-OFF-HEAT SET PR >> >> 2. Press SET. 3. Press to change MORN time in 30-minute intervals. 6 4. Press SET. > MORN temperature. 6. Repeat Steps 2-5 for DAY, EVE, and NITE. 7. Press SET to finish. 8. Shift COOL-OFF-HEAT switch to HEAT position. or PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON >> SET PR >> COOL-OFF-HEAT 9. Repeat steps 2-7 to program HEAT (winter) settings. > 5. Press to change NOTE: Both summer and winter programs use the same time settings. Your thermostat is now programmed for summer and winter operation. It will follow the four settings (MORN, DAY, EVE, NITE) for weekday operation and two settings (MORN and NITE) for weekend operation. Adjust the program at any time by following the steps as outlined above. Begin Programmed Operation 1. Place FAN: AUTO–ON switch Into AUTO. 2. Place COOL-OFF-HEAT switch Into COOL or HEAT Depending upon the season. 3. Press PROG/MAN button until indicator is in PROG position. PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON >> FAN: AUTO-ON COOL-OFF-HEAT COOL-OFF-HEAT SUMMER WINTER ET PROG/MAN PROG MAN >> PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON 7 Temporary Program Override To temporarily increase or decrease temperature or > Press > PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON >> >> The thermostat will automatically return to the program at the next scheduled setting change or after four hours. Manual Operation Manual operation allows continuous override of the program settings. 1. Press PROG/MAN until indicator is in MAN position. > > temperature settings. or >> PROG MAN SET PROG/MAN COOL-OFF-HEAT FAN: AUTO - ON T PROG/MAN PROG MAN >> Reset To reset the thermostat to factory pre-programmed conditions, press the reset button located directly to the right of the display. 2. Press to adjust PROG MAN CHANGE SET AUTO/MAN Elec Gas RHAM PM MORN DAY EVE NITE RC W Y G FAN AUTO ON RESET BUTTON COOL OFF HEAT 8 To Test Thermostat WARNING: DO NOT SHORT (JUMPER) ACROSS TERMINALS OF GAS VALVE OR SYSTEM CONTROL TO TEST OPERATION. THIS WILL DAMAGE THE THERMOSTAT AND VOID YOUR WARRANTY. CAUTION: Do not switch system to cool if the temperature is below 50°F (10°C). This can damage the air conditioning system and causepersonal injury. COOL-OFF-HEAT 1. Place the COOL-OFF-HEAT switch into the COOL position 2. Press the button until the temperature > setting is at least 3 degrees below the room temperature. The air conditioning system should turn on within a few seconds. NOTE: There is a built in 5-minute delay on break for compressorprotection. A second attempt to turn on the air conditioning will result in a 5-minute delay in compressor activation. 3. Put the COOL-OFF-HEAT switch into the OFF position. The air conditioning system should turn off. The fan may continue to run fo...