Stimmen - 2, Durchschnittliche Bewertung: 5 ( )

Hersteller: Honeywell Dateigröße: 714.5 kb Dateiname: 42998.pdf Unterrichtssprache:

4. Using the provided stickers, label each wire according to the chart. RC Y G W W (If the terminals are not labeled, contact a qualified HVAC technician.) note: Wire colors do not always comply with standards, so wire color should be ignored. refer to the existing terminal designation for proper identification. *If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-battery powered thermostats. 5. Do not let the wires slip back into the wall during disconnection. You may want to secure the wires to the wall as you disconnect them. After all wires are labeled, disconnect each wire and remove the existing wall plate. 11 Thermostat Top Cover 12 installing the thermostat installing the thermostat INSTALLING THE THERMOSTAT 1. Remove the top cover from the new thermostat by pulling the two halves apart. 1 14 WRC Y G WRC Y G installing the thermostat, cont. INSTALLING THE WALL PLATE 2. Position the new thermostat on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, level the thermostat and mark the wall for two holes. 4. Remove the thermostat and drill two 3/16” holes where marked. 5. Tap the plastic anchors into the holes until they are flush with the wall. 6. Reposition the thermostat on the wall, pulling the wires through the opening. Insert the mounting screws through the mounting holes and into the anchors. Verify that the thermostat is visually level and securely tighten both screws. 1 YBORHRCWGBOY GW RC RH 1 installing the thermostat, cont. CONNECTING THE WIRES 1. Loosen, but do not remove, the terminal screws. note: a jumper wire has been provided, connecting the rc and rh terminals for systems that do not provide both an rh and rc wire. if you have both an rh and rc wire, remove this jumper. if you do not have both an rh and rc wire, leave the jumper in place. 2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. Tighten each screw after the connection has been made. (The ends of any extra wires should be wrapped in electrical tape and carefully pushed back into the wall.) 3. Push any excess wire length back into the wall to prevent interference. 17 HGHE HP STD HE/HG Switch HP/STD Switch HE/HG Switch HP/STD Switch 18 installing the thermostat, cont. ATTACHING THE THERMOSTAT 1. Locate the HE/HG switch on the wall plate. Set the switch to HG for a gas furnace or oil burner. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.) 2. Locate the HP/STD switch on the wall plate. Set the switch to HP for Single-stage heat pump systems. Set the switch to STD for conventional systems. 19 20 installing the thermostat, cont. 3. Insert two fresh AA alkaline batteries. 4. Align the top cover with the the wall plate, and snap the two halves together. 5. Restore power at the electrical panel or furnace. 21 22 AUTO ON COOL OFFHEAT SYSTEM 90 07060580 Fan Switch SystemSwitch Set Temperature Slider AUTO ON COOL OFFHEAT SYSTEM 90 07060580 Fan Switch SystemSwitch Set Temperature Slider operation operation 1. Set the Set Temperature slider to the desired temperature. 2. The System Switch determines the operating mode of the thermostat. Select Cool, Off, or Heat. 3. The Fan Switch should normally be located in the Auto position. To run the fan continuously, slide the Fan Switch to the On position. note: in Auto , the fan will be turned on along with normal operation of your system. in a normal gas or oil f...

Herunterladen

Geben Sie zwei Ziffern: