Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Carrier Dateigröße: 558.98 kb Dateiname: Unterrichtssprache:

• Off is also used to access Setup AM and Program modes. Cool • In this mode, the thermostat controls the cooling system. • Press the Mode button to enter and exit the Program Cool mode. • In Program Cool mode (PROG displays), the thermostat will follow the program schedule that is stored in memory. Heat • In this mode, the thermostat controls the heating system. • Press the Mode button to enter/exit the Program Heat mode. • In Program Heat mode (PROG displays), the thermostat will follow the program schedule that is stored in memory. Hold • When in Programmable Cool or Programmable Heat, you can lock in the present settings indefinitely by pressing the Hold button once (PROG flashes). Press Hold button again to leave Hold mode (PROG solid). For a temporary Hold period, raise or lower set temperature to desired set temperature. The thermostat will automatically return to programmed set temperature after 2 hours. Setting the time and day of the week. The time and day of the week must be set for your program schedule to operate correctly. 1. Slide the Function switch to the Off position. 2. Press the Hold button in for 6 seconds. 3. Press the < or > button to adjust the time in hours. Press the Hold button once. Now press PMOFF PM the < or > button to adjust the time in minutes. 4. Press the Hold button while the time is displayed. The display shows the day currently set on the thermostat (01 = Monday, 02 = Tuesday, etc.). TODAY 5. Press the < or > button to set the current day of the week. Note: Sliding the Function switch to Cool or Heat positions will lock the values into memory. You may also press the Hold button to enter your programming schedule. Programming. Program Overview The programmable thermostat has four periods (MORN, DAY, EVE, NITE) that are customizable for each day of the week. Each period will have a set time, heat temperature and cool temperature. The thermostat monitors the day and time, while maintaining the specific conditions that you have chosen for each period in your program. Note: Operation being set will blink in the display. 1. Place the Function switch in the Off position. 2. Press the Hold button in for 6 seconds. 3. Press the Hold button 3 times. DAY (01–07) and PROG is displayed. DAY PROG 4. Press the < or > button to change the day you want to program (01 = Monday, 02 = Tuesday, etc.). 5. Press the Hold button to advance to the next parameter. Note: You can always press the Mode button to return to the previous parameter. • Period is displayed (MORN, DAY, EVE, NITE). 6. Press the < or > button to DAY MORN PROG change period of day. The display should blink the period of the day. 7. Press the Hold button to advance to the next parameter. • Set time is displayed. 8. Press the < or > button to adjust hours. Press the Hold button once, and then press the DAY AM PROG MORN < or > buttons to adjust minutes. 9. Press the Hold button to advance to the next screen parameter. Note: Transitions required after 11:59 PM must be programmed in the next day’s MORN period. Programming. AM DAY PROG MORN HEAT • Heat temperature is displayed (60°F to 85°F) 10.Press the < or > button to adjust heat set temperature. 11.Press the Hold button to advance to the next screen. • Cool temperature is displayed (60°F to 85°F) adjust cool set temperature. 13.Press the Hold button to advance to the next screen. Repeat steps 1–13 to program each day of the week individually AM DAY PROG MORN COOL or follow the instructions below to program every day the same as Monday. When programming is complete, slide the Function switch to Heat or Cool to exit Programming Mode. Repeat Programming Once the entire Monday (Day 01) schedule is set, the following procedure can be used to copy the Monday schedule for every day of the week. After the complete Monday schedule is set (see Programming, above), you will be at the “Day” screen: 12.Press the button to < or > 1. Press the < button once. Day 01 screen displays. 2. Press the < button and hold for DAY PROG 2 seconds. The days of the week stop flashing, locking the settings into memory. Once the schedule is locked in, you can go through each day and make any required changes. This feature speeds up the programming of the standard weekday/weekend schedule. 3. Slide the Function switch to Heat or Cool to exit Programming Mode. Factory preprogramming. The programmable thermostat comes preprogrammed with the following schedule: MONDAY thru SUNDAY MORN 6:00 AM DAY 8:00 AM EVE 6:00 PM NITE 10:00 PM HEAT 70°F HEAT 62°F HEAT 70°F HEAT 62°F COOL 78°F COOL 85°F COOL 78°F COOL 82°F Use the following personal program schedule to record your settings: MONDAY 01 MORN DAY EVE NITE HEAT HEAT HEAT HEAT COOL COOL COOL COOL TUESDAY 02 MORN DAY EVE NITE HEAT HEAT HEAT HEAT COOL COOL COOL COOL WEDNESDAY 03 MORN DAY EVE NITE HEAT HEAT HEAT HEAT COOL COOL COOL COOL THURSDAY 04 MORN DAY EVE NITE HEAT HEAT HEAT HEAT COOL COOL COOL COOL FRIDAY 05 MORN DAY EVE NITE HEAT HEAT HEAT HEAT COOL COOL COOL ...

Herunterladen

Geben Sie zwei Ziffern: