Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
RF Connector: Antenna/Cable 1, Antenna/Cable 2, and Loop Out Used to connect analog cable or antenna signals to the television, either directly or through your cable box. Video 1 and 2 Inputs Connects the video signals from various types of equipment. Y, Pb, Pr DVD Component Video and HD Component Video Some top-of-the-line DVD players use what is called “component video,” for extremely accurate picture reproduction. Refer to your DVD manual for further information. Connecting cables to your TV. Monitor Out Connects to a second TV or Monitor. (Monitor out is not available if you set lock “On” in Lock menu.) Left/Right Audio Used for stereo sound from various types of equipment. Component Left/Right Audio Used for stereo sound from various types of equipment. P A G E 8 206-03865 Front Connection Panel (Video 3) Video3 Panel VIDEO S-VIDEO AUDIO L/MONO IN 3 R There are four jacks on the right front side behind the screen on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connected to the front connection panel (Video3). To use the front jacks as the signal source, select them using Main Source menu as described on page 33. They will be named “Video 3” in the Main Source menu. Left/Right Audio Used for stereo sound from various types of equipment. Video Connects the video signals from any piece of equipment. S-Video A connection available on some very high-end equipment that provides better picture quality than video input. When you select Video3 (Front Video or Front S-Video, the Front audio) inputs are automatically selected as well. CAUTION: Do not connect to both Video and S-Video at the same time. Connect either Video or S-Video only. Mini glossary A/V CABLES Audio/Video cables. Three cable connector—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video (picture) and/or audio (sound) (VCR, DVD, cable box, or television). ANT / Cable Service Hookup Cable TV Wall jack 1 2 RF coaxial wire (75 ohm) Connect an antenna and/or cable service to your TV as shown. Turn to page 18 to do a channel search with EZ Scan for ANT / CABLE connection(s). RF coaxial wire (75 ohm) S-VIDEO ANT/CABLE1 INPUT ANT/CABLE2 INPUT LOOP OUT (R) (L) VIDEO (MONO) AUDIO Antenna MNT OUT IN 2 IN 1 If you receive your RF signal through an antenna that is several years old and connects with two small prongs, you will need to purchase a 300 to 75 ohm adapter. It should be available from your local electronics dealer. Zenith recommends using a 75 ohm cable for your antenna connections in order to prevent interference. For best signal reception, it is recommended to have your Antenna professionally adjusted. 206-03865 PAGE 9 Cable Box Connections Some cable services require the use of a cable box to decode premium channels and pay-per-view. Using the Loop Out to Decoder connection option, and programming your remote, you can connect your cable box so that you only need your MBR remote to tune to premium and non-premium channels. By connecting a cable box directly to your TV, as shown to the LOOP OUT, you make the cable box another available channel tuning source using your remote. 1 2 3 4 Locate the Antenna/Cable 2 jack on the back of your TV. Connect the cable that runs from the wall directly or antenna to the jack. Now find the Loop Out jack. Connect the cable from this jack to the Input jack on the back of your cable box. Cable box Locate the Output jack on the back of your cable box. Connect this to the Antenna/Cable 1 jack on the back of your TV. To view the premium stations, press the TV/VIDEO button on your remote and select the other Cable source (Ant/Cable 1). Then tune the channel number on your cable box for HBO, CINEMAX, SHOWTIME, etc. To view non-premium channels press the TV/VIDEO button and select Ant/Cable 2. Then run EZ Scan to find all available channels and store them in memory. This can be combined with any other equipment you may want to hook up, see following pages. Connect cable service wire directly to the TV, loop out from the TV, then to the cable box. From there, the cable box output connects to the next device in the connection series, until the last device, which connects back to the Antenna/Cable 1 jack on the TV. S-VIDEO ANT/CABLE1 INPUT ANT/CABLE2 INPUT LOOP OUT (R) (L) VIDEO (MONO) AUDIO MNT OUT IN 2 IN 1 In Out Cable TV Wall jack P A GE 10 206-03865 In Out Audio L R Video 3 4 S-Video S-VIDEO ANT/CABLE1 INPUT ANT/CABLE2 INPUT LOOP OUT (R) (L) VIDEO (MONO) AUDIO MNT OUT IN 2 IN 1 Antenna RF coaxial wire (75 ohm) Round wire (75 ohm) A/V cables not included with TV or VCR Back AV panel Cable TV Wall jack In Out Audio L R Video 3 4 S-...
Dieses Handbuch ist für folgende Modelle:Fernseher - R56W36 (1.4 mb)