Stimmen - 5, Durchschnittliche Bewertung: 3.6 ( )

Hersteller: JVC Dateigröße: 136.99 kb Dateiname: c0e04b42-116c-47c4-bdae-ec27cf26f8e8.pdf Unterrichtssprache:

These installation should be in accordance with the National Electrical Code ANSI/NFPA 70. Use the appropriate mounting hardware for the surface selected. WB-S621U Pendant Mount When a hole is not Reinforcement Angle Camera Mounting Plate Ceiling Panel Assy (for attaching TK-C625U/E and VN-C625U) 3. 1. 2. 5. made in the ceiling 4. Fall prevention FRONT Mark Protruding Part Ceiling Panel Assemb ly Positioning Hole Front Mark Top cover Bolt (M4) Safety cable Mount Hole ( 4.5 mm) Nut (M4) Groove Cable Safety cable Cables Screws (3 locations) 1.Make a hole in the ceiling. To route cables through the ceiling, make a hole of 30 mm ( 1 1/4) in the ceiling. 2.Route the safety cable and other cables Route the safety cable and cables that is attached to the reinforcement angle through the pendant mount. When a hole is not made in the ceiling, route the cables through the groove of the pendant Mount. 3.Mount the Pendant Mount to the Ceiling. Attach the pendant mount to the ceiling. CAUTION The camera may drop or images on the screen may appear shaky if the ceiling material is not strong enough. In this case, reinforce using a reinforcement materials. 4.Connect the safety cable. Upon removing the camera mounting plate, attach the safety cable (not supplied) to the safety cable mount hole ( 4.5 mm ( 1/8")) at the interior of the top cover using the M4 Bolt (not supplied) and M4 Nut (not supplied). When attaching the camera mounting plate, ensure that the Front mark on the camera mounting plate is facing a direction to the Front mark on the top cover. 5.Install the ceiling panel assembly (for attaching TK-C625U/E and VN-C625U) To install, align the protruding part of the ceiling panel assembly with the ceiling panel assembly positioning hole near the Front mark of the camera mounting plate. Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly. NOTE CAUTION Pay particular caution to the length, strength, pull and material of the safety cable in use to prevent the plate from falling. The screws are assembled to the ceiling panel assembly in such a way that they will not come off. 6.Connect the Cables. Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use. 7.Attach the camera's ceiling mount. (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E) Attach the camera's ceiling mount to the camera mounting plate using the 4 screws (M4 x 20 mm) supplied with the pendant mount. Ensure that the FRONT mark on the camera mounting plate aligns with the Front mark on the ceiling mount. WB-S622U Wall Mount 1.Make a hole When a hole is not To route cables through the wall, make a hole of 30 mm ( 1 1/8") in the wall. Front Mark 2.Route the safety cable and other cables Open the cover and route the safety cable and other cables through this wall mount. Please refer to "About Fall Prevention" for procedures to install the safety cable. When a hole is not made in the wall, route the cables pulled to the wall stand through the groove of the Wall Mount. 3.Attach the wall mount to the wall Attach the wall mount to the wall. 4.Connect the safety cable. Upon removing the camera mounting plate, attach the safety cable (not supplied) to the interior of the top cover using the M3 screw. (Refer to "About Fall Prevention".) When attaching the camera mounting plate, ensure that the Front mark on the camera mounting plate is facing a direction to the Front mark on the top cover. 5.Install the ceiling panel assembly (for attaching TK- C625U/E and VN-C625U) To install, align the protruding part of the ceiling panel assembly with the ceiling panel assembly positioning hole near the Front mark of the camera mounting plate. Ensure to tighten the screws (3 locations) assembled to the ceiling panel assembly. 1. 2. 3. Cover Mounting Screw Cover Camera Mounting Plate made in the wall 5. Front Mark Protruding Part Top cover Screws (3 locations) The camera may drop or images on the screen may appear shaky if the ceiling material is not strong enough. In this case, reinforce using a reinforcement materials. CAUTION Groove Safety cable Cables Ceiling Panel Assy Ceiling Panel (for attaching Assembly TK-C625U/E Positioning Hole NOTE and VN-C625U) The screws are assembled to the ceiling panel assembly in such a way that they will not come off. 6.Connect the cables. Connect cables to the camera. For details, please refer to "INSTRUCTIONS" section of the camera in use. 7.Attach the camera's ceiling mount. (Not applicable to TK-C205(A)U/E and TK-C205VP(A)U/E) Attach the camera's ceiling mount to the camera mounting plate using the 4 screws (M4 x 20 mm) supplied with the wall mount. Ensure that the Front mark on the camera mounting plate aligns with the Front mark on the ceiling mount. WB-S623U Ceiling Bracket 3. Cap Camera Mounting Plate Ceiling Panel Assy (for attaching 2. 5. 1. Front Mark Front Mark Top cover When a hole is not made in the ceiling Ceiling Panel Assembly Positioning Hole ...

Herunterladen

Geben Sie zwei Ziffern: