Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Troubleshooting
Before requesting service for this LCD TV, check the chart below for a possible cause of the problem you
are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and
restore proper operation. If you are in doubt about some of the check points, or if the remedies indicated in
the chart do not solve the problem, consult your dealer for instructions.
Symptom
Cause and remedy
page
–
Power supply does not go
• Is power supply plug unplugged from the outlet?
12
on
• If power will not go on with the remote control, is the power supply of the TV "Off"?
Remote control cannot be
• Is battery exhausted, or is battery polarity wrong?
7
operated
• Is the remote control receiver illuminated with strong light from a fluorescent lamp etc.?
–
• Are you using the special-purpose remote control for this equipment? (The unit
–
will not operate with another remote control.)
Image shakes, or image is
• Is there deterioration, breakage or disconnection of the antenna or antenna wire?
–
unclear
• Is the antenna wire connected correctly?
8, 9
There are spots on the
• Is the system affected (by radio wave interference or induced electromagnetic
p i c t u r e , o r t h e s c r e e n
waves) by external sources (automobiles or trains, high-voltage wires, neon,
shakes
motors, magnetized steel frame, or iron rain shutters, etc.)?
–
➠Turn off the power supply, and try changing the equipment setup location. If
that has no effect, separate magnet-proofing will be required.
The image appears doubled
• Is the antenna direction shifted?
–
or tripled
• Are reflected electromagnetic waves being received from mountains or buildings?
A color pattern appears, or
• Is the equipment being affected by another TV (electromagnetic interference)?
–
colors disappear
➠Changing the TV setup location may lead to improvement.
T h e c h a n n e l n u m b e r
• Has the RECALL button been pressed?
disappears from the screen
➠Press the "RECALL button" again.
–
If the system is switched to external input and there is no external signal video,
the number will disappear.
When the image is not stable,
• This occurs when the signal driving the liquid crystal is lost, and is not a
the screen turns completely
malfunction.
15
white for a moment
The screen goes dark momentarily
• The screen is darkened for a moment to conceal noise generated when changing
when the channel is changed.
channels.
–
The TV makes a hissing
• If the screen and audio are not abnormal, this sound is caused by slight
noise occasionally
expansion and contraction of the cabinet due to changes in room temperature.
–
It has no effect on performance.
The screen display shakes
• When input is switched to "video input", this may occur if there is no signal at
–
with video input
the video/audio input terminal.
A b l a c k b a n d a p p e a r s
• This is due to noise generated when changing channels.
momentarily when selecting
10, 11
channels with video
–
Both edges of the screen, or
• They may appear bent due to the received channel or some DVD software.
columns or window frames,
This is not a malfunction.
–
appear bent
The image from the connected
•Are plugs securely inserted into each terminal?
10,11
equipment does not appear
➠Securely insert plugs all the way.
The main unit is hot to the
• The main unit radiates heat, so some parts of the console reach a high
touch
temperature. This is not a problem for performance or quality.
• Set up at a location with good ventilation.
–
Do not cover the ventilation holes of the console with a tablecloth, etc., and do
not place on top of other equipment (like a video deck).
Poor Video
• Check HDMI cable is connected securely.
(Example: Snow noise, no
• Turn the power supply of the TV set and connected equipment ON/OFF.
H
picture, picture runs, etc.)
• Check compatibility of connected signal. Change settings of connected
12
D
equipment to make signal compatible.
• Is the input source from the equipment that is EIA/CEA-861/861B compliant
M
consumer electric device?
I
Poor Audio
• Set audio of connected equipment to L.PCM.
• Check setting of HDMI INPUT under AUDIO ADJUST.
24
• If the problem with the digital audio connection persists, change to an analog
audio connection.
46
...