Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Anleitung Monster Cable, modell SMARTVIEW 300L

Hersteller: Monster Cable
Dateigröße: 2.9 mb
Dateiname: SmartView_300L_trilingual_manual.pdf
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


.......... . ................ . .............. . .......... . WARNING ................ DO NOT OVER TIGHTEN SCREWS. Hanging the TV and Tilting Vertical Adjustment Bars on the Wall Plate Make sure the tilt mechanisms are locked before you mount the TV. For full instructions, refer to page 16. Monster strongly recommends that a minimum of two people perform the following steps. DO NOT release the TV until you are certain it is properly mounted and secured to the wall plate. 1) Connect the TV’s power cord and any AV cable to the TV before hanging it. With the help of a friend, lift the TV and plug its power cord into a nearby AC outlet. If routing AV cable in wall, route the cable through the wall plate’s Pass-Thru slots into the prepared opening in your wall. 2) Locate the two sets of QuickLift™ hooks on the back of the Tilting Vertical Adjustment Bars, now attached to your TV. 3) Hang either the upper or lower pair of QuickLift™ hooks on the wall plate’s top and bottom horizontal channels. (See diagram on opposite page.) 4) The higher display position requires an additional 3" of audio/video cable and power cord length. 5) Secure the display with the L-Shaped Locking Bar. Slide it horizontally through the slot below either bottom hook. 6) The locking bars should always be used to reduce the risk of seismic damage. A padlock can be added for additional theft deterrence. 15 .... .......... .......... .................. .......... ...................... .......... .............................. ........ ................ ........ .......... .... Adjusting Your TV’s Tilt and On-Wall Height Tilting Your TV: With a person on each side of the TV, turn the Pull ‘n’ Twist™ handles downward as far as you can. This loosens the tilting adjustment bars and initiates tilt. To further loosen the adjustment bars and increase ease of tilt, pull outward on the round portion of the handle. This initiates its ratchet mechanism. In ratchet mode, turn the handle upward to its highest point. Release the handle to disengage ratchet mode. When handle clicks into place, it’s ready to be turned downward again. Repeat Step 1. To prevent stress on TV, ensure both bars are tilted at the same angle. To lock the bars into place at the desired angle, do the reverse of the steps above. Turn the handles upward and ratchet as needed until the bars are secure. 1) 2) 3) 4) 5) 6) 16 ............................ .............................. .. .. .. Raising/Lowering Your TV: With a partner, disengage the QuickLift™ hooks from the wall plate and lift the TV. Re-engage the lower or upper set of QuickLift hooks to the wall plate’s top and bottom horizontal channels. 1) 2) Congratulations You’ve successfully installed your SmartView 300L FlatScreen Mount. Visit for more innovative Monster FlatScreen products, including our ultra low-profile FlatScreen Cable and our safe FlatScreen Clean LCD and plasma cleaning solution for preserving your flatscreen display. 17 .......... .......... .......... .......... ...................... .......... .............................. ........ ........ .. .. ................................ .............................. .... .... LIVE FOREVER LIMITED WARRANTY FOR CONSUMERS Monster, LLC, 7251 West Lake Mead Blvd., Las Vegas, NV 89128, (“Monster”) extends You this Limited Warranty. Statutory or common law may provide You with additional rights or remedies, which shall not be affected by this Limited Warranty. DEFINITIONS “Adequate Use” means use of the Product (i) within a home or dwelling, (ii) for private (as opposed to commercial) purposes, (iii) in conformance with all applicable local, state or federal law, code or regulations (including without limitation building and/or electrical codes), (iv) in accordance with manufacturer recommendations and/or instructions in the materials and documentation that accompany the Product, and (v) with proper electrical grounding. “Authorized Dealer” means any distributor, reseller or retailer that (i) was duly authorized to do business in the jurisdiction where it sold the Product to You, (ii) was permitted to sell You the Product under the laws of the jurisdiction where You bought the Product, and (iii) sold You the Product new and in its original packaging. “Formal Warranty Claim” means a claim made in accordance with the section “Formal Warranty Claims” herein. “Product” means a Product (i) that contained a reference to the “live forever” Limited Warranty, (ii) that You bought from an Authorized Dealer new and in its original packaging, and (iii) whose serial number, if any, has not been removed, altered, or defaced. “Product Defect” means an inadequacy of the Product that existed at the time when You received the Product from an Authorized Dealer and that causes a failure of the Product to perform in accordance with Monster’s documentation accompanying the Product, unless such failure has been caused completely or partly by (a) any use other t...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien