Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
We’re confident that the JBL system you have chosen will provide every note of enjoyment that you expected – and that when you think about purchasing additional audio equipment for your home, car, or office, you will once again choose JBL. Please take a moment to complete the enclosed profile card. It enables us to keep you posted on our latest advancements, and helps us to better understand our customers and build products that meet your needs and expectations. JBL Consumer Products read first! Before you begin included Two satellite speakers (with removable shelf stands). One pair of sat10 surround speakers with removable wall-mounting brackets. One subwoofer. features • 2-way satellite speakers with 3/4" titanium composite dome high-frequency drivers. • Triple chamber band-pass subwoofer. • Adjustable satellites with shelf stands included. One sat10 center speaker. • Adjustable, removable wall- mounting brackets (for use with surround speakers). • Video-shielded satellites. • Recessed wire channels on satellites and surrounds. • Diffraction-limiting foam satellite baffles. one. Speaker Placement Satellites Subwoofer 0-2 ft. Surround Speakers 5 . 6 ft. Mounting Options Satellites On shelves. On the wall. Optional bracket. Part No. SFX10BKT, or SFX10BKTWHT (white). Surrounds On optional stands. Part No. FS10/20. FS10/20WHT (white). On optional stands. On shelves. Wall-mounted. Brackets and hardware included. two. Speaker Connections Connection Tips For satellites, thread speaker wire through the hole in the bottom of the speaker, then feed it through the recessed wire channel. Separate and strip the ends of the speaker wire as shown. Speakers and electronics ter- minals have corresponding (+) and (–) terminals. It is impor- tant to connect both speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to (–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. + –+ + –+ – – ++ – – – + + – – Receiver Subwoofer Left Surround Right Surround Left Front sat10 Right Front sat10 Front Center Rear L R L R Left Right Output to Satellite Input from Amplifier Left Right + – Center Speaker + – – + – + – three. Testing Finally. Take a “test drive” with some favorite music or movies. 1. With the receiver/amplifier still turned off, confirm that its volume control is turned all the way down. Next, center the balance control. If the receiver/amplifier has an A/B speaker switch, set it to correspond to the speaker terminals connected to the SCS110 system. 2. Now, turn on your receiver/ amplifier and select a music source such as a CD player, cassette deck or FM tuner. 3. Turn up the volume control slowly until you hear sound from the speakers. Troubleshooting If there is no sound from any of the speakers, check the following: • Receiver/amplifier is on and a source is playing. • Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker, check the following: • Check the “Balance” control on your receiver/amplifier. • Check all wires and connections between receiver/ amplifier and speakers. • Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, or punctured. 4. Rotate the balance control all the way to the left. Sound should come only from the left speaker. If the sound comes from the right speaker with the balance control to the left, the speaker wires have been reversed during hook-up. Turn the receiver/ amplifier “off” and switch both sets of speaker wires. Dolby Pro Logic*-equipped devices (AV Receivers, Surround Sound processors or decoders, TVs or other sources) include a “test tone” you can use to balance the If the system plays at low volumes but shuts off as volume is increased, check the following: • Check all wires and connections between receiver/ amplifier and speakers. • Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, or punctured. • If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/ amplifier. volume of all the speakers in a surround sound system. Refer to the instructions accompanying your component for selecting the test tone mode and using it to balance speaker levels in your home theater. If there is low bass output, check the following: • Make sure the polarity (+ and –) of the left and right “Speaker Inputs” are connected properly. If there is no sound from the surround speakers, check the following: • Check all wires and connections between receiver/ amplifier and speakers. • Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, or punctured. • Review proper operation of your receiver/amplifier and its surround sound features. Specifications SCS110 System Power Handling 10 – 120 watts Frequency Response 40Hz – 20kHz (±3dB) Accessories such as the optional stands and brackets are available through your JBL dealer. For a deal...