Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Sony Dateigröße: 5.39 mb Dateiname: Unterrichtssprache:

Fotos und technische Daten  Sony  KDL-40X3500

• If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m (15 kgf·cm). 4 GB 3: Connecting an aerial/ 4: Preventing the TV cable/VCR from toppling over Connecting an aerial/cable Connecting an aerial/cable and VCR Coaxial cable (supplied) Mains lead (supplied) Scart lead (not supplied) VCR Mains lead (supplied) Coaxial cable (not supplied) Coaxial cable (supplied) Terrestrial signal or cable Terrestrial signal or cable Start- up Guide 5 GB 5: Bundling the cables ~ The hook of the cable holder can be opened from either sides depending on attaching position. 6: Performing the initial set-up 3, 4, 6, 7 3, 4, 6, 7 9 Selecting the language and country/ region 1 Connect the TV to your mains socket (220–240 V AC, 50 Hz). 2 Press 1 on the right side of the TV. When you turn on the TV for the first time, the Language menu appears on the screen. 6 GB 3 Press F/f/G/g to select the language displayed on the menu screens, then press . 4 Press F/f to select the country/region in which you will operate the TV, then press . If the country/region which you want to use on the TV does not appear in the list, select “–” instead of a country/region. Auto tuning the TV 5 Before you start auto tuning the TV, insert a pre-recorded tape into the VCR connected to the TV (page 5) and start play back. The video channel will be located and stored on the TV during auto tuning. If no VCR is connected to the TV, skip this step. 6 Press G/g to select “OK”, then press . 7 Press F/f to select “Antenna” or “Cable”, then press . If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for digital cable connection” on page 7. The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding. If a message appears for you to confirm the aerial connection No digital or analogue channels were found. Check all the aerial connections and press to start auto tuning again. 8 When the Programme Sorting menu appears on the screen, follow the steps of “Programme Sorting” on page 40. If you do not wish to change the order in which the analogue channels are stored on the TV, go to next step. 9 Press MENU to exit. The TV has now tuned in all the available channels. ~ When a digital broadcast channel cannot be received, or when selecting a country/region in which there are no digital broadcasts in step 4 (page 7), the time must be set after performing step 9. To tune the TV for digital cable connection 1 Press F/f to select “Scan Type”, then press . 2 Press F/f to select “Quick Scan” or “Full Scan”, then press . “Quick Scan”: Channels are tuned according to the cable provider’s information within the broadcast signal. The recommended setting for “Frequency”, “Network ID” and “Symbol Rate” is “Auto” unless your cable provider has supplied actual values to use. “Quick Scan” is recommended for fast tuning when this is supported by your cable provider. “Full Scan”: All available channels are tuned and stored. This procedure may take some time. This option is recommended when “Quick Scan” is not supported by your cable provider. For further information about supported cable providers, refer to the support web site: 3 Press G/g/f to select “Start”, then press . The TV starts searching for channels. Do not press any buttons on the TV or remote. ~ Some cable providers do not support “Quick Scan”. If no channels are detected using “Quick Scan”, perform “Full Scan”. Start- up Guide 7 GB Detaching the Table- Top Stand from the TV ~ Do not remove the Table-Top Stand for any reason other than to wall-mount the TV or to attach the optional TV stand. 8 GB Safety information Installation/Set-up Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries. Installation • The TV set should be installed near an easily accessible mains socket. • Place the TV set on a stable, level surface. • Only qualified service personnel should carry out wall installations. • For safety reasons, it is strongly recommended that you use Sony accessories, including: KDL-52X3500/46X3500/40X3500/46X3000/40X3000: – Wall-mount bracket SU-WL500 KDL-52X3500/46X3500/40X3500/46X3000/40X3000: – Floor stand SU-FL62 Transporting • Before transporting the TV except for KDL-52X3500 set, disconnect all cables. • Two or three people are needed to transport a large TV set. • When transporting the TV set by hand, hold it as KDL-52X3500 shown on the right. Do not put stress on the LCD panel and frame around the screen. • When lifting or moving the TV set, hold it firmly from the bottom. • When transporting the TV set, do not subject it to jolts or excessive vibration. • When transporting the TV set for repairs or when moving, pack it using the original carton and packing material. Ventilation • Never ...

Herunterladen

Geben Sie zwei Ziffern: