Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
-If you don’t succeed to browse the Internet using your wireless Ehternet bridge, please contact the retailer of the bridge (instead of Philips). ‘ Disconnect your wireless Ethernet bridge from the PC and connect it to the NETWORK connection at the bottom of your TV. ( Reconnect your PC to your network. Testing the wireless Ethernet bridge & Make sure the wireless Ethernet bridge is connected to the NETWORK connection at the bottom of your TV. e Switch on your TV. “ See “Testing your connection” on p. 9. Re-securing your wireless network Also see Annex 2:Wireless network security, p. 12. & Consult the user manual of your Wireless Access Point to apply its security setting according to the details you wrote down earlier. • Switch off the SSID broadcast. • Switch on wireless security (WEP/WPA keys). Note: If you don’t have your WEP/WPA keys you will need to create new ones and apply them to all wireless devices connected to your wireless network. e Disconnect your PC from your network. • In case of a wireless USB dongle, remove the dongle from your PC. • In case of an integrated wireless network adapter (e.g. laptop PC), disable the network adapter. • In case your PC has a wired connection, unplug the Ethernet cable from your PC. “ Connect the wireless Ethernet bridge to your PC. ‘ Consult the user manual supplied with the wireless Ethernet bridge to configure your device according to your current wireless network settings. If your PC can connect to the Internet using a web browser, the wireless Ethernet bridge is configured correctly. Note: After configuring your wireless Ethernet bridge you may need to wait a while before the connection is active.You may even have to restart the bridge. ( Disconnect your wireless Ethernet bridge from the PC and connect it to the NETWORK connection at the bottom of your TV. § Reconnect your PC to your network. Note: Also switch on the wireless security (WEP/WPA keys) of your wireless PC driver. Annex 2 : Wireless network security Attention Since wireless computer networks use radio signals, it is possible for other wireless network devices outside your immediate area to pick up the wireless signals and either connect to your network or to capture the network traffic. Consult the user manual supplied with your wireless Access point or wireless Ethernet bridge for further information. DO • Viruses, spyware and other malicious programs can undermine the security of your network. Use the appropriate software to protect your PC from these threats. • Change the default passwords for your network devices. Leaving these at default makes it easy for an outsider to gain access. Note: If you change passwords, write them down and store them in a safe location. • Use a router or a Wireless Access Point with Network Address Translation (NAT) or a firewall. • In a wireless network, enable the highest WEP key level that your hardware provides for. Upgrade your hardware, if possible. If you do not protect your wireless network, all data from your PC might be accessible to, for example, your neighbours or passers-by. • Switch off SSID broadcast on the Wireless Access Point. • Position your Wireless Access Point away from windows and towards the centre of your home. This decreases the strenght of the signal outside your home. • Some access points can control access based on the unique MAC address of the network devices trying to connect to it. See the documentation of your network devices to retrieve the MAC addresses. For the MAC address of your TV, see Annex 3, Manual Network Installation,View Network settings, p.13. DON’T • Don’t rely on radio transmission range limitations to secure your network. • Don’t use WEP/WPA keys and passwords that are easy to guess. • Don’t use passphrases to secure your wireless network as incompatibility with other brands of wireless network devices may occur. Annex 3 : Configuring your network settings manually Attention: If you have problems or questions or if you feel you don’t have sufficient knowledge about PC connectivity and PC networking, please contact your PC or TV retailer to assist you. TV menu Installation Manual network i... Languages View network sett... Country Network mode Time zone IP configuration Channels Manual network i.. Preferences Connections ............. Info DHCP/Auto IP or automatic network addressing is a protocol used to automatically connect network devices to a network. Please, refer to your router or wireless access point’s hardware instructions to see if this is supported. Static (or fixed) IP address: This is an IP address that your TV will always use to connect to your home network.When DHCP/Auto IP is not available, you can set a static IP address on your TV. A Subnet mask is used to define a subnet which is separated from all other networks by a router. The subnet mask indicates which part of the IP address is on the local network, and which must go out through the router. This menu allows you to do the network installation...