Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Use the accessory parts for fall-prevention to secure the Wide Plasma Display. • If the unit is knocked or children climb onto the pedestal with the Wide Plasma Display installed, the Wide Plasma Display may fall over and personal injury may result. Two people are required to install and remove the display. • If two people are not present, the display may be dropped, and personal injury may result. • Leave a space of at least 3 15/16 inches (10 cm) at the top, left and right, at least 2 3/8 inches (6 cm) at the bottom, and at least 2 49/64 inches (7 cm) at the rear. • Do not cover the air inlet holes at the bottom or rear of the display, or air outlet holes at the top, or a fire may result. Notes on handling 1) If the unit is placed in direct sunlight or next to a stove, the light and heat may cause discoloration or deformation. 2) Cleaning Wipe the unit with a dry cloth. If the unit is particularly dirty, clean it using a cloth soaked with water to which a small amount of neutral detergent has been added, and then wipe with a dry cloth. Do not use products such as solvents, thinner or household wax for cleaning, as they can damage the surface coating. (If using a chemically-treated cloth, follow the instructions supplied with the cloth.) 3) Do not attach sticky tape or labels, as they can make the surface of the pedestal dirty. Notes on installing the pedestal • Be sure to connect the power plug to an easily accessible power outlet. • Ensure there is free circulation of air around the equipment sufficient to keep the ambient temperature below 40.C. Failure to do this may cause the display to overheat, and malfunction may result. EnglishAttach the poles Parts for assembly Short screws .... 4 Long screws .... 4 Poles ............... 2 Pedestal ......... 1 Long screws .... 4 Poles ............... 2 Pedestal ......... 1 Securely attach both left and right poles to the top face of the base as shown below using short screws . Base Pedestal Pole Pole Stamped triangular mark Stamped circular mark Align the stamped marks. Align the stamped marks. Short screws Short screws Attach to the display console 1. Insert the poles into the holes in the display console. Display console(Rear of display) Model no. label Stamped triangular mark * Position the side of the pedestal with the model no. label to the rear. Push the assembly into the display until it stops. 2. Remove terminal cover. 3. Fasten with screws Display console(Rear of display) Claw Simultaneously hold in the two claws and remove the terminal cover. Display console (Rear of display) Long screws Long screws Securely fasten using long screws . * Work on a level and stable surface. 4. Connect cables 5. Fit the terminal cover. (Example of connecting cable routing) Display console(Rear of display) Clamps (Included with display) Display console (Rear of display) English English Tip-prevention parts Secure the console to prevent tipping * Securely attach to a wall, pillar or similarly solid structural feature using separately- obtained products such as cords or chains of adequate strength. ¦Attaching to a TV stand ¦Attaching to a wall . . . . . 77(3 1 / 32) 62(2 29 / 64) 390(15 23/64) 616(24 1/4) 704(27 23/32) 94(3 45 / 64) 49(1 59 / 64) 18( 45 / 64) 189(7 29 / 64) 198(7 51 / 64) 284(11 3 / 16) 156(6 9 / 64) 151(5 61 / 64) 146(5 3 / 4) 31(1 15 / 64) 684(26 59/64) Front screws..............3 Clamps..........2Band.................1 Wood screw......1 Units : mm (inches) Dimension diagram Screws Band Wood Screw Locate the wood screw at the center the material width. Screws Screws Clamps Wall . . . . . 77(3 1 / 32) 62(2 29 / 64) 390(15 23/64) 616(24 1/4) 704(27 23/32) 94(3 45 / 64) 49(1 59 / 64) 18( 45 / 64) 189(7 29 / 64) 198(7 51 / 64) 284(11 3 / 16) 156(6 9 / 64) 151(5 61 / 64) 146(5 3 / 4) 31(1 15 / 64) 684(26 59/64) Front screws..............3 Clamps..........2Band.................1 Wood screw......1 Units : mm (inches) Dimension diagram Screws Band Wood Screw Locate the wood screw at the center the material width. Screws Screws Clamps Wall Warranty English Panasonic Consumer Electronics Company Division of Matsushita Electric Corporation of America One Panasonic Way Secaucaus, NJ 07094 RACKS AND STANDS Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor” ), will replace parts in case of defects in materials or workmanship, free of change, in the USA or Puerto Rico, for ten (10) days from the date of the original purchase. In-warranty parts in the USA can be obtained during the warranty period be contacting: Panasonic Services Company (PASC) 20421 84th Avenue South Kent, Washington 98032 Tel.:1-800-833-9626 Fax.:1-800-237-9080 (6 am to 5 pm Monday-Friday; 6 am to 10:30 am Saturday; PST) Service in Puerto Rico can be obtained during the warranty period by calling the telephone number listed above. This warranty is extended only to the original purchaser. A purchase receipt or other proof of the original purchas...