Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: NEC Dateigröße: 1.08 mb Dateiname: Unterrichtssprache:

The keystone function is used in this distortion adjustment. Hold the CTL button down and use the KEYSTONE +/buttons to adjust the left and right sides so that they become parallel. FOCUS + CTL [Keystone distortion] - KEYSTONE [No distortion] When the KEYSTONE item is set to [ON], this adjustment condition will take effect when the power is switched on. See "Selecting Keystone Distortion Correction and Storage" on Page E-40. Temporarily Turning Off the Picture and Audio This function is used to temporarily turn off the picture or the audio. Picture ......... A press of the PICTURE button will turn off the picture. Another press will result in the picture being projected. Audio ........... A press of the AUDIO button will turn off the audio. Another press will result in the audio being output. MUTE PICTURE AUDIO The background color of the screen will be black when the picture is turned off. Returning the RGB Input Signal to the Standard Adjustment This function is used when something has gone wrong with the screen at the time of RGB signal entry. The function is valid when the on-screen menu is not being displayed. Press the SETUP button, then press the ENTER button. ENTER SETUP Select an item from among the adjustment data stored to standard memory that is close to the input signal. When readjustment is necessary, adjust the screen or call up an item that is close to the input signal from within the user memory. Upon a return to the standard adjustment, the YCbCr input setting becomes RGB input. When a switcher is connected, the various items of the switcher return to the default settings. (The sync termination setting will be high impedance.) Memory Search This function is valid when the on-screen menu is not being displayed. Press the SETUP button, then press the LOAD button. If you've modified the settings in memory, use this function. Remote Control Address Setting When two or more projectors (GT2000/GT2000R) are used with wireless remote control operation, identification (ID) is given to the projectors and remote control so that other projectors are not controlled erroneously. Projectors having the same ID can be controlled. A)Hold down the CTL button and press the Adr. button (VOLUME t ). The address display appears. Address RC Unit 01 B) Use the number buttons to enter a 2-digit ID that is the same as the ID of the projector that is being controlled. Addresses that can be specified are from 00 to 64. Press the ENTER button to set. When a mistake is made in the entry, press the CLEAR button and start the entry again from Step A). * The projector ID of the main unit can be checked with [Settings Menu] ® [Projector ID] of the main menu. * Setting the ID of the remote control to 00 permits remote control operation irrespective of the ID of the projector. * If the batteries are removed from the remote control, the remote ID will return to "00". E-43 ADJUSTING THE PICTURE AND THE AUDIO (Picture) These functions adjust the picture and audio with the on-screen menu display. When the input signal is selected with the user memory or the channel memory and the auto memory save function is set to [On], the adjustment data is overwritten. Default Picture Settings Picture settings at the time of shipping from the factory are as described below. Please set required items. Press the MENU button to display [Main Menu], select [Picture] with the cursor button, then press the ENTER button to display the picture. Main Menu Picture Settings at the Time of Shipping from the Factory Picture Alignment Memory Switcher Display Menu Brightness Contrast Volume Color Tint Names of items that cannot be adjusted with the currently selected input mode are displayed in gray. Settings Menu Sharpness Source Image Mode Normal White Balance Scan Mode Interpolation RGB/YCbCr Auto PC Mode RGB – + 0 Contents of the selected item are displayed. Adjusting the Picture (Brightness, Contrast, Color,Tint, and Sharpness) Adjust these items to an optimum level in conjunction with the input image. Select [Picture] from the main menu, then press the ENTER button. When the item to be adjusted is selected, the adjustment bar of the selected item is displayed at the bottom edge of the display. Change to the (–) direction +- Change to the (+) direction The various adjustment ranges are from -31 to +32. Picture Brightness Contrast Volume Color Tint Sharpness Image Mode White Balance Scan Mode Interpolation RGB/YCbCr + -10 – E-44 Item § (–) Button © (+) Button Notes Brightness Becomes darker Becomes lighter –––– Contrast Picture becomes fainter Picture becomes denser –––– Color Color becomes paler Color becomes deeper RGB input does not apply Tint Becomes more reddish Becomes more greenish RGB, PAL and SECAM input do not apply Sharpness Picture becomes softer Picture becomes more distinct RGB input does not apply Adjusting the White Balance (White Balance) This function corrects the black and white level of the input signal and adjusts the color reproduc...

Herunterladen

Geben Sie zwei Ziffern: