Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Philips Dateigröße: 967.42 kb Dateiname: 9a221fa0-6188-4211-99f4-0f8e6bb90066.pdf Unterrichtssprache:

You can give 90 TV stations a programme number from 00 to 89. If required, a name can be programmed for the TV station found (max. 5 positions). • Press button (CD) <1 or t>, so that the required letter and the required digit are found: • Press button ENTER -?>. Select following letter or digit, etc. Repeat the operation until the station name has been stored. In this way a name can be allocated to a maximum of 34 TV stations. Note. It is possible to call up the programmed station names of TV stations already adjusted via DOS (as a check). • Press button O, the list appears on the screen. • Press button C±) again to switch off DOS. D. • Press button D (<>) and keep it pressed in until indicator PR no longer flashes. The TV station, possibly with the programmed station name, will now be established under the selected programme number. An extending red bar may also appear in the top of your picture by way of confirmation. Searching for and storing other TV stations For searching and storing the remaining TV stations (max. 90), repeat operations A, B, C and D. ET o a Calling up list If required you can call up the list of the possible programmed station names with their corresponding programme number. • Press button Q) and keep it pressed in until the list appears on the screen. • Press button C3 again to switch off DOS. Erasing programmed TV station names (DOS) • Select the appropriate programme number. • Press button A O). 0 ON SCREEN A -*-► Z -e> • Press buttons <1 I> (CD) at the same time. Five ‘stars’ now appear where the TV station name was displayed. • Press button D «>)• An extending red bar may also appear in the top of your picture by way of confirmation. The programme number and the station name are now erased from the DOS menu. 4 B - 0 + Personal preference setting of picture and sound Here also you can switch on DOS (see appropriate section ‘Calling up DOS’). Note. The contrast and the HUE are not reported via DOS. Picture and sound have already been set in the factory in accordance with the average standard. It is however possible to set both picture and sound according to your personal preference and to store these settings in the memory. As a result the factory setting is cancelled. Setting To do this, press the plus + or minus — side of the relevant controls. Volume - •& + Brightness •§> - 9> + ETT Bass 9‘ Balances EF ran SELECT PROG. À s C/P • Press button D (<>). The changes Implemented are now stored In the memory. ET BF VERTICAL CD T ET ‘Static convergence’ If the picture quality Is adversely affected by external interference (magnetic fields), the reason for this could be that the convergence is not properly adjusted. This can be checked and corrected as follows: • Open the cover. • Keep button C3 pressed until a cross pattern appears. The cross which now appears on the picture should consist of a white horizontal and a white vertical line. It this Is not the case and lines of different colours are visible, proceed as follows: • Turn the buttons +/— RED HORIZONTALS VERTICAL m so that the red lines coincide with the fixed cross already on the screen. • Turn the buttons +/— BLUE HORIZONTAL B VERTICAL CD so that the blue lines coincide with the fixed cross already on the screen. This must result in a white horizontal and a white vertical line which together form a cross. • Press button G) again to switch off the test position. Note: Do not place loudspeakers (magnets) in the vicinity of the projection TV because these can affect the static convergence. 5 Operating the TV nr © Switching on/off • To switch on: Press button ©. (The TV switches on to programme number 1.) At the top right of the picture PR 1 may appear, possibly with the name of the station. № The indicator ® will also come on. Note 1: If indicator (!) lights up, you must press a digit button on the remote control. Note 2: You can switch off the TV by pressing button ® again. TV mode II a I I From TELETEXT mode and EXTERNAL*, switch back to TV programme choice. • Press button O. * External refers to modes 1C3* or 2 Q*- for sets linked to the Euroconnector external 1 and/or external 2. Programme selection Select the required programme number with the digit buttons. • First press button -/•- for programme numbers which consist of 2 digits. • Back to one-digit programme numbers. • Press button again. Note: When selecting a programme number, the selected programme number and, if required, the programme station name appear on the top right of the screen for ± 3 sec. With stereo broadcasts ‘STEREO’ appears at the same time. With dual language sound, the text DUAL I or DUAL H will also appear. U y - @ + I il Il--4P y - + Il-il H AAAA + c/p t&j O y “ $ + i—j y - 9= + li-il y n D> 'Cl Il-jl u AAAA + c/p ¡¿s O y n Changing picture and sound settings Here you can also switch on DOS (see appropriate se...

Herunterladen

Geben Sie zwei Ziffern: