Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Panasonic, modell CT13R16V

Hersteller: Panasonic
Dateigröße: 940.18 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

A chemical reaction could result causing permanent marring of the finish. Remote Control Transmitter Do not use benzene, thinners or other petroleum based cleaners to clean the Remote Control Transmitter. To clean, wipe with a soft cloth slightly moistened with a mild detergent and then wipe dry with a soft clean cloth. -4- Installation Receiver Location This unit is intended to be used with an optional stand or entertainment center. Consult your dealer for available options. Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the screen. Use of some types of fluorescent lighting may reduce remote control transmitter range. Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or moisture. To insure optimum color purity do not position magnetic equipment (motors, fans, other speakers, etc.) nearby. Optional External Equipment Connections The Video/Audio connections between components can be made with shielded video and audio cables. For best performance, video cables should utilize 75 ohm coaxial shielded wire. Cables are available from your dealer or electronic supply house. Before you purchase any cables, be sure you know what type of output and input connectors your various components require. Also determine the length of cable you’ll need. AC Power Supply Cord CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT OF AC OUTLET AND FULLY INSERT. DO NOT USE THIS (POLARIZED) PLUG WITH A RECEPTACLE OR OTHER OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. Polarized Plug Remote Control Battery Installation Batteries: Use two “AA” batteries. 1. Remove the battery compartment cover on back of the remote. 2. Install the batteries in the battery compartment. (Polarity (+) or (-) must be correct.) 3. Reattach the battery cover. Helpful Hints: For frequent Remote Control users, replace old batteries with Alkaline batteries for longer life. To Remove Cover Push tn And Up On Catch With A Narrow Object Precaution on Battery Use Incorrect installation can cause battery leakage and corrosion that will damage the Remote Control Transmitter. Observe the Following Precautions: 1. Batteries must be replaced as a pair. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (Example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when Remote Control reacts sporadically or stops operating the TV. or EUR501372 (WHITE) -5- Installation (cont.) Antenna/CableConnections Antenna Connection - For proper reception of VHF/UHF channels, an external antenna is required. For best reception an outdoor antenna is recommended. Antenna Mode must be set to TV. (Refer to Antenna Mode section.) 75 Ohm Incoming Cable from Home Antenna 300 Ohm Indoor Typical VHF/UHF Antenna VHF/UHF on Back of Set VHF/UHF on Back of Set or 300 to 75 ohm Matching Trans-former(Supplied 13” Models Only) Cable Connection - For reception of cable channels, connect the cable supplied by your local cable company. Antenna Mode must be set to CABLE. (Refer to Antenna Mode section.) Incoming Cable from Cable Company 75 Ohm VHF/UHF on Back of Set NOTE: Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable converter box is required for proper reception. Check with your local Cable company for compatibility requirements. Other Video Equipment VCRs, Video Disc Players, Computers, TV games, and DSS equipment can also be connected to the antenna input connection. How to Install VHF/UHF Dipole Antenna (13” Models Only) A VHF/UHF antenna and matching transformer are supplied. Push the stem of the VHF/UHF antenna into the antenna hole on the cabinet back as shown. Extend the antenna and adjust its length, direction and angle for the clearest picture. BACK OF RECEIVER -6- Optional Equipment Connection and Operation Rear Audio/Video Input Connection NOTE: TURN OFF Rear Audio/Video Input device before TURNING ON the Front Audio/Video Input device. If both are ON at the same time it will cause an Audio/Video interference between the two input signals. Operation 1. Connect the Optional Equipment as shown to Front or Rear Audio/Video Input Jacks. If Optional Equipment is Stereo, place Optional Equipment in Monaural Mode and use either left or right Audio Output jack. 2. Select the Video mode by pressing the TV/VIDEO button. 3. Operate optional equipment as instructed in Optional Equipment manual. -7- Location of Controls Remote Power Button Press to turn ON or OFF. Mute Button Press to mute sound. A second press resumes sound. Press also to access and delete Closed Caption display. Volume Buttons Press to adjust TV sound level. Use with Channel buttons to navigate...