Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Ultratec Dateigröße: 1.63 mb Dateiname: Unterrichtssprache:

(See page 27 for instructions on how to program the remote to control your VCR.) To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The CBL button will blink, indicating that the remote will now control your cable box. (See page 28 for instructions on how to program the remote to control your cable box.) To operate your set-top-box, point the remote at the remote sensor of the set-top-box and press the SET-TOP-BOX (STB) button. The STB button will blink, indicating that the remote will now control your set-top-box. If you have a satellite receiver, use this button to prorame your satellite receiver. (See page 29 for instructions on how to program the remote to control your set-top-box.) To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The DVD button will blink, indicating that the remote will now control your DVD player. (See page 30 for instruction on how to program the remote to control your DVD player.) To operate additional audio/video equipment, point the remote at the remote sensor of the component you wish to control and press the AV1, AV2 or AV3 button. This button will blink, indicating that the remote will now control the desired component. (See page 31 for instructions on how to program the remote to control additional Audio/Video equipment.) ©- I© 0 © ©! _| — SOURCE WIZARD ■— ' i© © © ©! [© ©1 1© © ©i !© © © EEP © LAS о ojdo б CH rt VOL •iL •P '"**• 's.'*» Q- £ o 0 o o 1 I PIP ACCESS J PIP MODE SWAP O o o PP^ TV/VCR c, r o¡ o ®! REC HITACHI CLU-5711TSI i© © 0 ©] — SOURCE WIZARD - |(dV^ (Amp) [© "©■ ©1 i© © ©i !© © © EEP © LAS o 0^0 JO Ô o o o PIP ACCESS PIP MODE SWAP o o o PP^ TV/VCP c, run, r 0¡ O ®! REC HITACHI CLU^^TSI ^ These buttons allow the remote to control your TV, VCR, cable box, satellite receiver, DVD player, or other Audio/Video equipment depending on which mode is chosen, as explained above. ©,© LIGHT BUTTON When you are in a dark room, press the light button @ on the remote to light up the buttons shown in @ and the source button will blink. The light will stay on for about 8 seconds if the light button is not pressed again. These buttons will not appear to light if the room is too bright. NOTE: 1. Your remote control “SOURCE WIZARD” buttons are either labeled as “AV1, AV2 and AV3,” or “CD, TAPE, and AMP.” If your remote control “SOURCE WIZARD” buttons are labeled as “AV1, AV2, and AV3,” please program your Audio/Video components as follow for best performance. Use “AV1” to program your CD brand. Use “AV2” to program your TAPE brand, and use “AV3” to program your AMPLIFIER/RECEIVER brand. AV1-Use for CD brand AV2-Use for TAPE brand AV3-Use for AMPLIFIER/RECEIVER brand. ■ SOURCE WIZARD---- 2. Your remote control button to directly access the THEATER MODE is either labeled as “PIX” or “MODE”. POWER 20 HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV 0 POWER button Press this button to turn the TV set on or off when the remote is in TV mode. (See page 22 for instructions on how to set the remote control to TV mode.) (0 TV button When the TV button is pressed, it will blink, to indicate the remote is in TV mode. 0 VCR button When the VCR button is pressed, it will blink to indicate the remote is in VCR mode. (see page 27) 0 CABLE (CBL) When the CABLE button is pressed, it will blink to indicate the remote is in CABLE mode. (see page 28) 0 SET-TOP-BOX (STB) When the STB button is pressed, it will blink to indicate the remote is in STB mode. (see page 29) If you have a Satellite receiver, use this button to program your Satellite receiver. (see page 29) (Q DVD button When the DVD button is pressed, it will blink to indicate the remote is in DVD mode. (see page 30) 21 HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR TV © AV1, AV2, AV3, or CD, TAPE, AMP buttons When pressed, each of these buttons will blink to indicate the remote is in Audio/Video mode. (see page 31) NOTE: Your remote control “SOURCE WIZARD” buttons are either labeled as “AV1, AV2 and AV3,” or “CD, TAPE, and AMP.” If your remote control “SOURCE WIZARD” buttons are labeled as “AV1, AV2, and AV3,” please program your Audio/Video components as follow for best performance. Use “AV1” to program your CD brand. Use “AV2” to program your TAPE brand, and use “AV3” to program your AMPLIFIER/RECEIVER brand. AV1-Use for CD brand AV2-Use for TAPE brand AV3-Use for AMPLIFIER/RECEIVER brand. • SOURCE WIZARD ■ AV1 ) I AV2 CHANNEL selector buttons CHANNEL selector buttons are used to set FAVORITE CHANNELS, CHANNEL MEMORY, etc. Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes appear next to the channel display on your TV, t...

Herunterladen

Geben Sie zwei Ziffern: