Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Hitachi Dateigröße: 1.36 mb Dateiname: Unterrichtssprache:

ANT button Use the ANT (Antenna) button to select between the VHF/UHF and AUX (Auxiliary) antenna inputs. NOTE: When VHF/UHF is selected, the channel number in the upper right corner of the screen is green. When the AUX input is selected, the channel number is in yellow. MENU, ENTER, CURSOR buttons All the on-screen display features can be set or adjusted by using these buttons. The "MENU" button will start or exit the on-screen display. The "CURSOR" buttons will highlight functions or adjust different features. The "ENTER" button will set features to your preference. CHANNEL SELECTOR buttons "CHANNEL SELECTOR" buttons are used to set the time, for channel memory, etc.. Channel selection may also be performed by pressing channel up ( ) or down ( ). NOTE: The TV may not receive some channels if you are not in the correct AIR/CABLE mode. (See page 29) AVX button The AVX (Auxiliary Video) button will select between the antenna signal and the three sets of video input jacks each time the button is pressed. If the Picture-in-Picture (PIP) is on, the AVX will select between the three sets of video input jacks. (See page 21) VOLUME, MUTE buttons Press the "VOLUME" up ( ) or down ( ) button until you obtain the desired sound level. To turn the sound off instantly to answer the telephone, etc., press the "MUTE" button. Press the "MUTE" button again or press the "VOLUME" up ( ) button to restore the sound. The word "MUTE" will remain displayed if the CLOSED CAPTION feature is turned off. CLOSED CAPTION will also be displayed when the "MUTE" button is pressed. The word "MUTE" will not be displayed if the CLOSED CAPTION feature is on. LAST CHANNEL (LST-CH) button Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.) PICTURE-IN-PICTURE buttons See separate section on page 21 for a description. SURROUND (SRD) button Press this button to enter the SURROUND menu. (See pages 15 and 42.) ARTIFICIAL INTELLIGENCE (AI) button Press this button to turn the AI function on or off. (See page 38) PICTURE-IN-PICTURE (PIP) The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing a VCR program (TV or tape) on any of the video inputs. PIP BUTTON Press the "PIP" button and a sub-picture appears in one corner of the screen. Press the button a second time to remove the sub-picture from the screen. Press the AVX button when the sub-picture is on to change between VIDEO: 1, VIDEO: 2 and VIDEO: 3. The TV channel will always be either the main picture or the sub-picture. SWAP BUTTON If you wish to switch what is being shown on the main picture to the sub-picture, press the "SWAP" button. SHIFT BUTTON To move the sub-picture to another corner, press the "SHIFT" button. The sub-picture moves one step counter-clockwise every time the "SHIFT" button is pressed. FREEZE (FRZ) BUTTON If you wish to freeze the sub-picture, press the "FRZ" button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the button again. STROBE FREEZE Press this button without a sub-picture to freeze one or four frames of the picture you are currently viewing. Press this button again or PIP to return to normal viewing. The four frame strobe freeze is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing. CAUTION: A pattern burn may develop if the sub-picture is left in the same corner permanently. If the PIP feature is used frequently, occasionally shift the sub-picture to a different corner. NOTE: 1. Only sound from the main picture can be heard, unless you choose PIP from wireless mode and use the "TRANSMITTER OUT" outputs on the rear panel. (See page 44.) 2. Each strobe freeze frame is delayed about 0.3 (3/10) second. USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the pre-coded function for your VCR This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system in your VCR. (Refer to page 26) 1. Set the MULTI-PAGE select switch to "VCR". 2. Turn ON your VCR. 3. Aim the remote control at the front of your VCR. 4. While holding down the VCR POWER button on the remote, enter the 2 digit preset code that matches your VCR as shown on page 26. The remote will turn off your VCR when the correct 2 digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off after 5 seconds, try a different 2 digit preset code. 5. The remote will now control your VCR. NOTES: 1. If your VCR cannot be operated after performing the above procedures, this means that your VCR's codes have not been precoded into the remote. 2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your V...

Herunterladen

Geben Sie zwei Ziffern: