Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Texas Instruments Dateigröße: 1.44 mb Dateiname: Unterrichtssprache:

©3M 2003. All Rights Reserved. Operation 3M™ Digital WallDisplay Shutdown Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit. The lamp will turn off and the projector arm will return to its housing. The On/Off Button will flash amber as the arm closes. Note: There is a 30-second reset period before the On/Off Button will function again. During this period, the On/Off Button will flash red. The fan will continue to run for approximately five minutes to cool the unit. Note: If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on for your convenience. Do not turn off the Master Power Switch or unplug the power cord before pressing the On/Off Button. After the On/Off Button is pressed, the fan continues for approximately five minutes to cool the 3M Digital WallDisplay. ©3M 2003. All Rights Reserved. 3M™ Digital WallDisplay Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover. The Trigger Button is underneath the front IR Sensor of the remote control unit and can be pressed easily with the index finger. FORWARD KEYPAD POWER R MOUSE MENU INPUT BLANKMUTE POINTER FREEZE REVEAL TIMER VOLUME + IR SENSOR Transmits infrared signals to 3M Digital WallDisplay unit. LED Indicates that remote control unit is transmitting signal. POWER Press to turn 3M Digital WallDisplay on/off. MUTE Press to turn the audio (speaker) function on/off. TRIGGER BUTTON Press for left-mouse button functions. DISK PAD Press to control the computer’s mouse, navigate the menu system, or control the Pointer or Reveal functions. R MOUSE Press for right-mouse-button function in mouse mode. MENU Press to display onscreen menu system. BLANK Press to turn the screen- blanking function on/off. INPUT Press to change source of input. REAR KEYPAD VOLUME Press to adjust the speaker and Audio Out sound level. TIMER Press to turn on/off display of countdown timer. POINTER Press to turn the pointing function on/off. FREEZE Press to turn the still-mode function on/off. REVEAL Press to uncover part of the screen from top to bottom or from left to right. ©3M 2003. All Rights Reserved. Remote Control Unit 3M™ Digital WallDisplay Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn off the sound. Press again or press the Volume + or -buttons to restore sound. Disk Pad Press to: • control the computer’s mouse when using the Mouse function. • select menu items and adjust values in the onscreen menu system. • control the Pointer position while using the Pointer function. • control the path of the Reveal function. While using the onscreen menu system or Pointer function, the computer Mouse function is temporarily disabled. To regain computer mouse control, turn off the current function or the onscreen menu system. Note: The USB or serial mouse cable must be connected between the 3M Digital WallDisplay and the computer when using Mouse mode. R Mouse Acts as the right-mouse-button when the mouse function is active. Menu Press to display the onscreen menu system or to cancel display. Blank Press to make the screen go blank. Press again to return to normal display function. Input Press to change the source of input for 3M Digital WallDisplay. The Input button cycles between Computer, DVI, Composite Video (RCA jacks), and S-Video. .. .. ©3M 2003. All Rights Reserved. 3M™ Digital WallDisplay Remote Control Unit Remote Control Unit Rear Keypad Pointer Press to turn the pointing function on/off. A green dot will appear on the screen. The dot can be controlled by pressing the arrows on the Disk Pad. Volume Press the + button to increase or the -button to decrease the speaker loudness level. When the audio is muted, the Volume + or -buttons will also cancel the Mute function. Timer Press to turn the timing function on/off. The timer will display on the screen and begin to count down. To change the Timer value, refer to the On Scrn Timer sub-menu in the Tools menu. Freeze Amoving image can be stilled or ‘frozen’ when the Freeze button is pressed. To release the Freeze function, press the Freeze button again. Reveal Press to turn the screen-reveal function on/off. Press the Disk Pad in the desired reveal direction (e.g. press down to reveal from the top down, etc.). Trigger Button On the underside of the remote control unit, beneath the IR sensor, press button for left-mouse-button functions. POWER R MOUSE MENU INPUT BLANKMUTE POINTER FREEZE REVEAL TIMER VOLUME + ©3M 2003. All Rights Reserved. Remote Control Unit 3M™ Digital WallDisplay 3M™ Digital WallDisplay ...

Herunterladen

Geben Sie zwei Ziffern: