Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Bell'O Dateigröße: 1.35 mb Dateiname: Unterrichtssprache:

Final tightening of the bolts should always be done by hand, with a Phillips-head screwdriver or ratchet wrench. English English When mounting to solid concrete, bricks, or cinder block After you have determined your desired TV location, tape the Installation Template (IT) in place securely on the wall with masking tape. Use a level to double check that the screw holes line up vertically, as shown in Figure 8. Figure 8 Do not drill into mortar joints! Mortar joints are in between the bricks where the cement is. These joints are typically not strong enough to hold heavy loads. You need to drill the holes at least one inch from the joint to provide adequate strength. Use a standard drill with a new masonry drill bit to drill the holes. Do not use a hammer drill because it can damage the hole or break out the back of the concrete wall which will not give adequate support to the anchor. Because drilling an accurate and clean hole is essential to securing your mount, be sure to use a new drill bit. An old drill bit can not only make an uneven hole, it can also break out the back of the concrete block which can diminish the holding ability of the anchor. Line up the installation template to ensure you’re not going to drill into any mortar joints. Drill four evenly spaced holes 3" (76mm) deep using a 5/16" (or 8mm) size drill bit. Follow the directions on the installation template carefully. IT Concrete Block Wall Level English This kit includes the TOGGLER® brand ALLIGATOR® Anchors (U) for mounting in concrete walls, brick, or cinder block. These patented anchors are the finest solid wall anchors on the market and offer excellent holding ability when properly installed. After the holes are drilled, remove the template and place four ALLIGATOR® Anchors into the concrete wall as shown in Figure 9. Figure 9 U After you have prepared the holes for mounting the Wall Plate (WP), install the wall plate by inserting the four Lag Bolts (T) through the mount and into the ALLIGATOR® Anchors (U) as shown in Figures 7 and 10. After checking that the wall plate is level, tighten all lag bolts fully, but be careful not to over-tighten. Figure 10 WP U T Concrete 3" (76mm) minimum hole depth Installing the decorative End Covers Even though your TV hides most of your wall mount from view, from the sides you can probably still see the ends of the bracket. This kit includes decorative End Covers (EC) to make your bracket installation look clean and finished. To install the end covers, simply line up the cover with the end of the bracket, and press into place. Look for two holes in the frame of the bracket, which the end cover inserts into, as shown in Figure 11. WP EC Figure 11 Step 3: Mounting the TV Step 3: Mounting the TV Understanding the locking mechanism Your TV Wall Mounting Kit For Dummies has a unique feature which enables you to easily lock the Monitor Arms (MA) onto the Wall Plate (WP) so that your TV cannot be removed. Before attempting to attach the TV with the monitor arms to the wall bracket, make sure that the right and left side locking mechanisms are in the unlocked position. Using a screwdriver, turn the large screw head on the side of the bracket 90° toward the front of the bracket, as shown in Figure 12. Figure 12 Large Screw Head Locking Bar Shown Up in Unlocked Position To Unlock Don’t forget those wires! If your audio, video, and power cables will not be accessible after you mount the TV, you need to make those connections now. Before doing this, however, make sure all TV and component power cords are not plugged into any electrical outlets and your audio and video equipment is turned off. Make sure you leave enough slack so you can install the mount without any interference. English Mounting the TV Figure 13A MA WP DETAILED VIEW Before you attempt to attach the TV to the wall plate, make sure the adjustable arms are parallel to the TV (in the 0-degree position). This position is indicated by the markings on the arms as shown in Figure 13B. Detailed instructions on how to adjust the arms can be found on page 17. When you’re ready to put the TV with the Monitor Arms (MA) onto the Wall Plate (WP) assembly, get a friend or an assistant to help you lift the TV and guide the monitor arms onto the wall plate as shown in Figure 13A. Markings on the adjustable arm will line up when in the 0-degree position. Figure 13B Make sure the arms are engaged on both the top and bottom rails of the wall plate! English Locking the arms into place After the TV with the Monitor Arms (MA) is positioned on the Wall Plate (WP), you need to lock the arms into place so that the TV cannot inadvertently come off the wall plate or be removed. To lock the arms, simply turn the large screw head on the side of both of the bracket’s locking mechanisms 90° toward the wall using a screwdriver as your assistant holds the TV in place. (See Figure 14.) After you've done this, and the locking mechanism has been engaged, tighten the M4 x 10mm Securi...

Herunterladen

Geben Sie zwei Ziffern: