Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Sanus Systems, modell TELEVISION TURNTABLES TV20

Hersteller: Sanus Systems
Dateigröße: 488.84 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Paul, MN 55113 800.359.5520 7.6.04 TVTurntable (sold separate) SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar SupportPillar Support PillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillarPillar BaseBaseBaseBaseBaseBaseTV Turntable (sold separate) Pillar SupportPillar SupportPillar Support Base Step 1: Remove the swivel from the TV Turntable by removing the Phillips Screw in the center of the swivel as shown in the Dia- gram to the right. Step 2: Use the same Phillips Screw removed from Step 1 to fasten the swivel to the base of the TV-VCR Kit. Insert the Phillips screw through the center hole of the swivel and proceed to thread it into the appropriate pilot hole in the center of the TV-VCR Kit as shown in the Diagram on the right. Tighten the Phillips Screw with a phillips screw driver until tight. NOTE: When using the TV20 use the front Pilot Hole. When Using the TV27 or TV32 use the rear Pilot Hole. Step 3: Insert the Plastic Dowels into the larger holes in the Support Pillar as shown in the Diagram on the right. Gently tap the Plas- tic Dowels in with a hammer if needed. Repeat step for the other Support Pillar. Step 4: Thread the Allen Bolts up through the Base of the TV-VCR Kit, and into the corresponding holes in the Support Pillar. Tighten Allen Bolts with the provided Allen Key until they are tight. Step 5: Add the TV Turntable to the TV-VCR Kit by setting the Turn- table on top of the Support Pillars so the dowels in the Support Pillars line up with the holes in the bottom side of the turntable. Press the Turntable down firmly until the bottom of the Turn- table is flush with the top of the Support Pillars. Phillips Screw Bottom ofBottom ofBottom of TurntableTurntableTurntableTurntableTurntableTurntableTurntablePhillips Screw TV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit BaseTV-VCR Kit Base Front Pilot Hole Rear Pilot Hole Plastic DowelsLarger HoleLarger HoleLarger HoleLarger HoleLarger HoleLarger HoleLarger Hole Support Pillar Top of TV-VCR BaseTop of TV-VCR BaseTop of TV-VCR BaseTop of TV-VCR Base Nylon Swivel is Allen Bolts Located on the Bottom Top of TVTurntableTop of TVTurntableTop of TVTurntableTop of TVTurntableTop of TVTurntableTop of TVTurntableTop of TVTurntablePlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlasticPlastic DowelDowelDowelDowelDowelDowelDowelTop of TV-VCR Kit Front of Assembly Turntable Larger HoleNylon Swivel isNylon Swivel is Top of TV Turntable DowelDowelDowel Sanus Systems 2221 Highway 36 W. St. Paul, MN 55113 800.359.5520 7.6.04 Front of Assembly Larger HoleLarger HoleLarger HoleLarger HoleLarger Hole Remove the swivel from the TV Turntable by removing the Phillips Screw in the center of the swivel as shown in the Dia- gram to the right. Step 2: Use the same Phillips Screw removed from Step 1 to fasten the swivel to the base of...