Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If the studs are 12” apart, use three 3” lag bolts for the top row of mounting points and three 3” lag bolts for the lower row mounting points. If the studs are 16”, 18” or 24” apart, use two 3” lag bolts for the top row of mounting points and two 3” lag bolts for the lower row of mounting points. Step 1 Step 2 Step 3 Determine where to mount the Once all of the studs have been located, use Using a 1/4” drill bit, drill a pilotAM250/AM250-FLIP. Use a stud a pencil to mark the spots. Place the mount hole at the first aligned and markedfinder to find the exact center of against the wall and align the mount to the location. each stud. marked stud locations. Step 4 Step 5 Step 6 After the pilot hole has been drilled, line up the mounting slot opening to the drilled hole. Insert one (1) 5/16" x 3" lag bolt and washer into the mounting hole and tighten (see WARNING: below). With the help of an assistant, place a level on the center of the mounting rail and level the mount. Mark and drill the second mounting hole. Insert one (1) 5/16" x 3" lag bolt and washer into the mounting hole and tighten (see WARNING: below). Repeat steps 5 and 6 for the remaining mounting points. Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. If the studs are 12” (304.8mm) apart, use three 3” (76.2mm) lag bolts for the top rail and three 3” (76.2mm) lag bolts for the lower rail. If the studs are 16”(406.4mm), 18” (457.2mm) or 24” (609.6mm) apart, use two 3” lag bolts for the top rail and two 3” lag bolts for the lower rail. Installation Instructions Page 7 AM250 Page 8 Installation Instructions Universal Mounting Bracket Assembly Step 1. Place the display on a soft, flat surface, face-down. Step 2. Determine where the mounting points are located. Step 3. Place the universal brackets over the mounting points. If the mounting surface is not completely level, use the spacers (see Page 6) to ensure that the universal brackets are level on the display. Step 4. Once the desired position has been determined, place the Griplate™ over each mounting point (dimples facing up) and secure them using the appropriate hardware (see Page 5). For the two upper mounting points, the dimples (Griplate™) must be facing up. For the two lower mounting points, the dimples (Griplate™) must be facing down. Concrete Mounting Concrete anchors must be used for concrete installation. They can be purchased at your local hardware store. The mounting surface must be a minimum 6” thick. Step 1. Begin by placing the mount into position against the wall, keeping it level. Step 2. Mark off four holes to be used for securing the mount. Step 3. Next, drill holes using a masonry bit for your anchors (recommended 5/16” masonry bit). Step 4. Insert a commercially available concrete anchor into each hole (recommended 3/8” wedge anchors). Step 5. If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall. Step 6. Once all of the anchors are in place, move the wall bracket into position. Step 7. Attach the nut onto the threaded shaft that is protruding from the wall. Step 8. Do not tighten until all nuts are in place. Dimples M4 M5 M6 M8 DIMPLES FACING UP DIMPLES FACING DOWN DIMPLES FACING UP DIMPLES FACING DOWN AM250 Attaching the Display IT IS RECOMMENDED THAT TWO PEOPLE MOUNT THE DISPLAY, AS THE UNIT IS HEAVY AND, IF DROPPED, WILL DAMAGE THE MOUNT, THE DISPLAY, AND/OR PERSONNEL. Upper Mounting Bar Lower Mounting Bar Step 1. Place the universal brackets and the display over the upper mounting bars of the AM250. Upper Mounting Bar Lower Mounting Bar Step 2. Lower the universal mounting brackets and display onto the mounting bars of the AM250. Step 3. This is what the two units will look like after the universal mounting brackets and display are mounted to the AM250. Installation Instructions Page 9 AM250 Securing and Leveling the Display Once the brackets have been placed over the upper mounting bars on the AM250, use two (2) M6 x 30mm Phillips Head locking screws to secure the brackets to the bottom of the mounting bars. This will prevent lateral shift movement. Level your flat panel by installing the two additional M6 x 30mm Phillips Head screws to the upper bracket assembly as shown below. Once the display is level, tighten the locking screws. M6 x 30mm Phillips Head Screw Lower Locking Point Tilt Positioning Upper Bracket LevelingAdjustment Screw to tilt back. Display Tilt Tension Adjustment Page 10 Installation Instructions AM250 Installation Instructions Page 11 Technical Specifications All measurements are in inches (mm). 14.03 (356.36) 16.00 (406.40) 1.50 (38.04) 3.55 (90.17) 28.00 (711.20) 28.79 (731.79) 3.00 (76.20) 12.53 (317.5) 20.40 (510.54) 27.00 (685.80) 29.64 (752.86) AM250 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product ...
Dieses Handbuch ist für folgende Modelle:Fernseher - AM250-FLIP (4.84 mb)