Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Front Rear PC INPUT RS-232C PORT SPEAKER(8 Ohms) L R L R AUDIO RGB/COMPONENT INPUT EXTERNAL PORT G/Y B/Pb R/Pr H V AUDIO R L PC INPUT RS-232C PORT EXTERNAL PORT SPEAKER(8 Ohms) AC IN L R L R AUDIO RGB/COMPONENT INPUT G/Y B/Pb R/Pr H V AUDIO R L Power • Power control sensor • Power Standby: Red - Standby Green - ON Power button Used when upgrading, etc. BNC G/Y, B/Pb, R/Pr, H, V Input Used when connecting PDP to External Equipment PC INPUT External Speaker Power Select when adjusting volume or select/adjust “MENU.” Press when moving “MENU.” STAND BY/OPERATE Remote Control Remote Control Note • Use two “AAA” batteries. • Be sure to use replacement batteries of the same type as the original ones. * The number in ( ) indicates the page in which • The life of a battery depends on how much the function of each button is explained in detail. it has been used. When Using Remote Control: •Be sure not to allow the Remote Control to drop or to become wet. •Keep it away from hot or moist locations. Installing the Batteries in your Remote Control: •To remove the cover, slide it outwards while pressing it down. •Place two batteries in the remote control by properly orienting them, then close the cover. INPUT SELECT POWER DISPLAY ZOOMPICTURE MODE SCREEN MODEFREEZE MUTESOUND MODE SLEEP ZOOM+ MENU VOL VOL Input Select button Used to select a desired input. Every press of the button cycles through the five different modes: PC -> Component 1(RGB H/V) -> Component 1 Used to zoom the screen. To enlarge, press the (+) button, and to return to the previous condition, press the (-) button. (ZOOM Mode: Zoom 0~20) Select Menu by pressing (Up), (Down), (Left), (Right) buttons. Every press of the button cycles through the four different modes: Normal --> Dynamic --> Cinema --> User. Every press of the button cycles through the five different modes: Normal --> Movie --> Music --> News --> User. Mutes sound. Pressing the Power button of the Monitor allows the Display to be in standby. (Red light is shown in the Remote Control Sensor.) At this time, if you press the Power button of the Remote Control, the Display is turned ON (Green light in the Sensor). Indicates the current state and resolution. Used to display a desired menu. Adjusts the volume. Adjusts the size of the screen (Normal, 16:9, etc.) Used to view a still picture during watching moving images. (Sound can be heard.) Each time you press this button, a different input mode appears. The sequence is as follows: 15 Min. -> 30 Min. -> 60 Min. --> 90 Min. -> 120 Min. -> OFF After the time is selected, it automatically goes standby when the selected time elapsed. 20Menu Select button 26 Screen Select button 19 Sound Mode button 29 Mute button Aspect Ratio 22 Still 28 Sleep Timer 34 Power button Display button ZOOM button Menu button 30 Volume button 20 14 Installation Instructions When Using the Stand (Assembled Picture) M5 SCREWS Take out the STAND from the 1package. Engage the assembled stand 3with 4 screws (M5) enclosed. Smoothly fit the Stand to the 2Plasma Display Panel 4Erect the Display * When installing PDP Main Unit, be sure it is done by more than 2 professionals. * For detailed installation information, refer to the User’s Manual, “STAND”. Separate the Protective Caps. (They are used when using for wall mounting, so store them.) 15 1Connecting the Speaker to the Stand 2Connecting the Speaker Cable • By using a (-) driver or coin, fasten the special screw securely. Be sure to check if there is a sponge attached to the surface on which the speaker is contacted. • Connect one set (two cables) of the cable to the terminals on the back of the speaker in the way that red cable is for (+) terminal and black cable for (–) terminal. Stand Connecting the Speaker to the PDP Connecting PC • DAEWOO PLASMA supports resolution of VGA, SVGA, XGA, SXGA, UXGA. • Before connecting a PC to the PDP, be sure to adjust the resolution of PC. • This product is not supported by Plug and Play, so select Standard Monitor when setting PC monitor. Connecting PC 16 Connect the PC to the PDP. • Prepare the PC cable (D-sub 15pin) and the PC audio cable(Sold separately). • Connect the PC(Output) to the PDP(Input) as shown below. 2 Before connecting to the PDP, set the resolution of the PC. • Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen. • Choose the SETTINGS tab in the DISPLAY Menu. • In the SETTINGS Menu, select 640x480 or 800x600. 1 PC INPUT L R AUDIO PC INPUT RS-232C PORT SPEAKER(8 Ohms) L R L R AUDIO RGB/COMPONENT INPUT EXTERNAL PORT G/Y B/Pb R/Pr H V AUDIO R L 15 PIN D-sub PC Audio Press the Power button. • Turn on the PDP and the PC. 3 4 4 Input Select • Select [PC] by pressing the INPUT INPUT SELECT button of the Remote Control or SELECT PDP unit. • Each time you press the INPUT SELECT button, a different input mode appears. The sequence is as follows: PC --> Component 1(RGB H/V) --> Component 1. PC Component1(RGB H/V) Component1 5 5 Enjoy Dynamic Ultra Screen Monitor by Using PC’...
Dieses Handbuch ist für folgende Modelle:Fernseher - DP - 42 SP (1.53 mb)
Fernseher - DP - 42 WP (1.53 mb)