Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Fisher Dateigröße: 1.09 mb Dateiname: Unterrichtssprache:

Use the driver (3 mm, Green) included with the lens to remove the screws. Be careful not to drop the lens when removing the screws. After using, save the driver for latter use. 4 MOUNT THE LENS (See Figure-5 and 6) 1. Remove protective caps (front and back) on the lens. 2. Mount the lens on lens mounting bracket with 4 screws. (locate motor on left side). Use the driver (4 mm, Yellow) included with the lens to fasten the screws. After using, save the driver for latter use. 3. Connect the lens motor lead to the connector "K16J" of the circuit board. 4. Connect the lens motor lead to the lead holder. Fig-7 Fig-8LENS COVER LIGHT-BLOCK SHEET LIGHT-BLOCK SHEET BASE 5 MOUNT THE LIGHT-BLOCK SHEET BASE (See Figure-7) 1. Mount the light-block sheet base to the projector. 6 MOUNT THE LIGHT-BLOCK SHEET AND LENS COVER (See Figure-8) 1. Mount the light-block sheet to the light-block sheet base as shown in the Figure-8. (In the same position as the removed sheet has been placed). Use the sheet included with the lens. 2. Make sure the part no. and mark (TOP and BACK) on Light-Block Sheet and set them properly. 3. Mount the lens cover with the screws. -3 LENS REPLACEMENT PROCEDURE (FOR "B" TYPE) Perform the steps 1 to 6 for lens replacement. 1. 2. 3. Fig-2 LIGHT-BLOCK SHEET BASE FRONT CABINET LENS COVER LIGHT-BLOCK SHEET SCREW "A" SCREW "A" SCREW "A" Fig-1-1 Fig-1-2 Fig-1-3 LENS COVER FRONT CABINET LENS COVER FRONT CABINET FRONT CABINET First set the lens at the fully lower position with lens shift adjustment. REMOVE THE LENS COVER AND FRONT CABINET 1. 2. 3. Turn the lens cover to counter-clockwise and pull it toward front and remove the Lens Cover. Remove 2 Screws-A. Remove the front cabinet See Figure-1-1 and 2. 1. Remove 2 Screws-A. 2. Remove the front cabinet See Figure-1-2 and 2. Pull Lens Cover toward front and remove it. Remove 2 Screws-A. Remove the front cabinet See Figure-1-3 and 2. 2 REMOVE THE LIGHT-BLOCK SHEET BASE AND LIGHT-BLOCK SHEET (See Figure-2) 1. Slide the light-block sheet base upward and remove it. 2. Remove the light-block sheet from lens. -4 3 REMOVE THE LENS (See Figure-3 and 4) 1. 2. 3. Remove the lens motor connector from terminal. Loosen the screws-B (2 screws) which fastens the lens. {Use the driver (4 mm, Yellow) included with the lens to loosen the screws.} Slide the lens lock latches to "UNLOCK" position and remove the lens. Be careful not to drop the lens when removing the screws. After using, save the driver for latter use. Fig-3 SCREW "B" LENS LOCK LATCHES CONNECTOR TERMINAL 4 MOUNT THE LENS (See Figure-5) LENS LOCK LATCHES LOCK POSITION UNLOCK POSITION Fig-4 1. 2. 3. 4. Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with Upper 2 screws. (locate motor on left side). Use the driver (4 mm, Yellow) included with the lens to fasten the screws. Remove the lower 2 screws on the Lens. (Lower 2 screws are not used.) Slide the lens lock latches to "LOCK" position and lock the lens. (See F...

Herunterladen

Geben Sie zwei Ziffern: