Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Use the DVI-HDMI cable, plug the HDMI end to "INPUT" port of the Transmitter and the DVI-D end to PC or DVD Player's DVD-D video port. Connect the power adapter to the "5VDC" and plug into the power outlet c. System Turn ON: Turn on your DVI output device and monitor to confirm the functionality of the display. The "M1 LINK" LED of the Transmitter should display orange to confirm the connection of a local DVI monitor. d. Remote Monitors: Make sure the remote monitor(s) to be connected to the DVI-C5-R Transceiver can display the broadcast video resolution. Avenviewsnview.com 6 e. EQ Adjustment: You can adjust the EQ control to Auto mode by rotating the EQ control Anticlockwise. The "EQ" and "AUTO" LEDSs will display blue. After connecting the extender system, if you see dynamic dots on unclear image on the DVI, you need to adjust the signal from Transmitter. f. EDID Simulation: The Transmitter has built-in EDID simulator. When local DVI monitor is connected to Transmitter, it will automatically record the EDID data from DVI Monitor. When a local DVI monitor is not connected the Transmitter will simulate the EDID data and activate the DVI signal on the PC or DVD Player. DVI-D Monitor DVI-D Power Adaptor To OVI-D Output of PC or player DVI-C5-R Installation a. First Time Connection: Connect DVI Monitor's DVI Cable to the receiver and TURN ON the monitor. b. Device Connection: Plug power adapter to DVI-C5-R (Transceiver), the "PWR" LED and "M1 LINK" will turn ON. The other "LINK" LED should turn off because there is no input of video signal from "LINK IN" port. c. EQ Adjustment: You can adjust the EQ control to Auto Mode by rotating the EQ Anticlockwise. The "EQ" and "AUTO" LEDs will turn ON Blue. If noise or unstable image is seen on the local DVI monitor, it indicates the DVI signal received by the Transmitter needs to be adjusted. You can also adjust the EQ control for better image display. This changes the EQ into manual mode. The "EQ" and "AUTO" LED will turn off to indicate the manual EQ Mode. Avenviewsnview.com 7 DVI-D Monitor * * A № - ft DVI-D Power Adaptor Selection of Cable a. Selection: Most makes and versions of Cat 5/5e/6 cables will work with DVI-C5-S Transmitter and DVI-C5-R Transceivers. However, since the quality and characteristics of Cat 5/5e/6 cables varies it has been found that some perform better than others. The major factor influencing the transmitting distance is the skew property of the cables. Skew represents the difference in propagation delay between the fastest and slowest set of wire pairs. A lower skew will mean a longer video transmitting distance. Cat 5/5e/6 cable with a skew of lower than 15ns/100m should enable a cascading length of: < 80m (275ft) @ 800 x 600 < 50m (175ft) @ 1024 x 768 < 40m (150ft) @ 1280 x 1024 b. Skew Property: A Cat 5/5e/6 cable with a skew lower than 15ns/100m should enable a cascading length of < 80m (275 ft) at 800x600, <50m at 1024x768, and < 40m at 1280x1024. Avenviewsnview.com 8 c. Termination: The RJ45 terminations to the Cat 5/5e/6 cable must be made to the EIA 568B specifications. 1. Orange White 2. Orange 3. Green White 4. Blue 5. Blue White 6. Green 7. Brown White 8. Brown The EIA/TIA definition of 568B in the pin assignment PAIR 3 PAIR 2 >/pAIRl^v PAIR 4 A I A I A 1 2 3 4 5 6 7 8 JACK POSITION Avenviewsnview.com 9 d. Connect the Cable: Plug one ends of UTP cable to DVI-C5-S Transmitter's "LINK IN/OUT" port and the other end to the DVI-C5-R Transceiver's "LINK IN/OUT" port. The monitor connected to the Transceiver should now display and the "LINK" LED should turn green to indicate the DVI signal activation. Use EQ control to adjust the video quality for best signal. Installation Diagram of DVI-C5-S and DVI-C5-R e. Extending Audio Signals: The DVI-C5-S Transmitter and DVI-C5-R Transceiver are not able to extend audio signals. Use a pair of Avenview AUD-RJ11 Audio Extenders with 4-wire phone cable and RJ11 connectors to extend the audio signal. General Troubleshooting Problem Possible Solution Off-Center Screen Image, Odd Colors or No Picture • Try adjusting the brightness, sharpness, contrast, and color balance controls of your monitor. • Try adjusting the centering and positioning controls of your monitor to position the picture on the screen. No Image • Ensure that the monitor cable is securely fastened to the DVI and Monitor port. Avenviewsnview.com 10 Installation of Multiple Transceivers and Display a. Multiple Transceivers: By using additional DVI-C5-R Transceivers, it is possible to extend the system almost indefinitely to remote DVI-D displays. Installation Diagram of Multiple Transceivers Ensure that common grounding is maintained to minimize ground loops and interference for larger group of cascaded Transceivers. Avenviewsnview.com 11 Specifications DVI Transmitter and Transceiver Model DVI-C5-S DVI-C5-R Description 1 Port DVI-D Transmitter 1 Port DVI-D Transceiver ...