Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1.4 Introduction Avenview FO-HDMI-XX-MM Series with fiber optic cable system lets you extend digital flat panel signal up to 100 meters (330 feet) without signal degradation by at 1080p resolution. - High Speed and long distance transmission by Optical fiber - Fully compatible with HDMI 1.3 - Supports 12 bit Deep Color - Uses standard Type A HDMI receptacle - DDC and CEC signal and 5V power line are transmitter by copper line - HDCP Compliant 1.5 Model Description FO-HDMI-XX-MM Model Name Length in Meters (5 = 5 meters, 10 = 10 meters) 1.6 Package Contents Before you start the installation of the converter, please check the package contents. - HDMI Optical Cable with Transmitter and Receiver x 1 - User’s Manual x 1 1.7 Before Installation . Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction. . Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity. . Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire. . Do not twist or pull by force ends of the optical cable. It can cause malfunction. 1.8 Installation Avenview FO-HDMI-XX-MM is composed of a Transmitter converting the graphic signal of a computer to optical and Optical Fiber propagating the optical signal and Receiver supplying electrical signal to monitor converted from the optical signal to electrical signal. The Transmitter should be connected to computer and the Receiver should be connected to a monitor. Avenview FO-HDMI-XX-MM is designed to self-detect the resolution of the monitor and change the resolution accordingly. Follow these steps for connecting to a device: To setup Avenview FO-HDMI-XX-MM follow these steps for connecting to a device: 1. Power on your display 2. Connect Transmitter to the PC and Receiver to the Display. 3. Connect the optical fiber between Transmitter and Receiver. 4. Restart the computer. Use the DC power adapter (optional) with correct specification. The Transmitter which is connected to a computer uses power from the computer. Do not twist or pull by force the both ends of the optical cable. It may cause malfunction Section 2: Specifications Item Description Units FO-HDMI-XX-MM (Transmitter) FO-HDMI-XX-MM (Receiver Unit Description HDMI Fiber Optic Transmitter HDMI Fiber Optic Receiver HDMI Compliance HDMI 1.3 DVI Compliance DVI 1.0 HDCP Rev 1.1 Input Signal TMDS Signal (HDMI 1.3 Standard) Output Signal TMDS Signal (HDMI 1.3 Standard) Video Bandwidth 12bit Deep Color / 60Hz Supported Resolution & Distance Up to WUXGA (1920x1200), 1080p @ 100 meters ( 330 feet) Optical Converter 4 ch 850 nm Multi-Mode VCSEL 4 ch GaAs PIN photo Diode HDMI Connector 19 pin HDMI Plug Fiber Type 50/125 .m Multi-mode glass fiber Power Consumption 0.8W (max) 1.05W (max) Bending Radius 70mm Dimensions (L x W x H) 1” x 2.9” x 0.8” Environmental Operating Temperature 32. ~ 104.F (0. to 40.C) Storage Temperature -4. ~ 140.F (-20. ~ 60.C) Relative Humidity 20~90% RH (no condensation) Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. 2.1 Part List Item Description Q’ty Material A DVI-D Single Link 18 Plug 2 Glass filled thermoplastic UL94V-0 B DVI Case-Top, Bottom 2 Glass filled PC UL94V-0 C DVI Thumb Screw 4 SUM 24L+ABS D Stopper 2 PVC 55% E Epoxy Printed Circuit Board for Tx 1 FR-4, 1.5t UL94V-0 F Optical Connector for VCSEL,PD 2 PA46 UL94V-0 + C5210 G Optical Connector for fiber 2 PA46 UL94V-0 H Epoxy Printed Circuit Board for Rx 1 FR-4, 1.5t UL94V-0 I Vertical Surface Emitting Laser Diode 4 GaAs J Photo Detector 4 GaAs K 4 fiber 5 copper DVI Optic Cable 1 See Section 4 L 4 fiber DVI Optic Cable 1 See Section 4 M Label 4 Polyester-matte 3.3mil N DC Power Jack 2 Polyamide 6/6 O DC Power Adaptor 1 E191362 (UL No) 2.2 Power Consumption and DDC Power Requirements Power consumption of FO-HDMI-XX-MM Transmitter and Receiver Module Item maximum units Transmitter 0.8 Watt Receiver 1.05 Watt Transmitter module of FO-HDMI-XX-MM without external power supply is operated by drawing out power for DDC from the computer and receiver module of FO-HDMI-XX-MM cable also utilize the DDC power delivered via copper wire. If graphic board of the computer does not supply over 0.6A, 5V, FO-HDMI-XX-MM cable may not operate normally. 2.3 Signal Pin Assignment Transmitter / Receiver Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2+ 9 T.M.D.S. Data0- 17 DDC/CEC Ground 2 T.M.D.S. Data2 Shield 10 T.M.D.S. Clock+ 18 +5V Power 3 T.M.D.S. Data2- 11 T.M.D.S. Clock Shield 19 Hot Plug Detect 4 T.M.D.S. Data 1+ 12 T.M.D.S. Clock- 5 T.M.D.S. Data 1 Shield 13 CEC 6 T.M.D.S. Data 1- 14 Reserved (N.C on device) 7...