Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Connect the right (red) and left (white) audio output from the source to the right (red) and left (white) input on this unit (Audio cable not included). Make sure you connect both audio and video from the same source to YUV IN. Note: When connecting a DVD player to the television, the picture resolution is solely dependent upon the resolution supported by the DVD player attached. DVD Player resolutions vary from 480i to 1080i, and this television can support DVD players up to a maximum resolution of 1080i. * May require a subscription for receiving HD channels, check with your cable/satellite service provider for details. CONNECTIONS HD SOURCE with component video output (Digital Cable Box*, Satellite Receiver*, or external over-the-air HD-Tuner) PLV1615CS1- E1-23.pmd 12 20/04/2007, 15:35 CONNECTIONS CONNECTING AN AUDIO AMPLIFIER This connection allows you to use an audio amplifier and external speakers. Connect the right (red) and left (white) audio OUTPUT from this unit to the right (red) and left (white) audio INPUT on your amplifier. Refer to your amplifier’s user manual for more information. Note: To control the audio, both the TV and the amplifier must be turned on, and the volume of the amplifier must be set above 0, or you will not hear any sound. If you want to hear the sound from the amplifier only, press the VOL – button on the TV to decrease the volume or press the MUTE button on the remote control to turn off the sound. CONNECT THE POWER CORD • Connect the AC power cord into a wall outlet. • Press the STANDBY/ON button on the unit or remote control to turn on the unit. To AC outlet Note: • Be sure the AC power cord is disconnected and all functions are off before making connections. • Make sure that all the components are connected correctly. • To prevent electrical shock, match wide blade of plug to wide slot of wall outlet, then fully insert. • When you are not going to use the unit for a long period of time, disconnect the power cord. 13 PLV1615CS1- E1-23.pmd 13 20/04/2007, 15:36 14 INSTALLATION MOUNTING ON THE WALL This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 3” x 3” (75mm x 75mm) mounting kit designed for flat-panel TVs (sold separately). Mount this unit according to the directions included with the mounting kit. Note: You must remove the base stand before mounting the unit on the wall. REMOVING THE BASE STAND WARNING: The LCD Display is very fragile, and must be protected at all times when removing the base stand. Be sure that no hard or sharp, or anything that could scratch or damage the LCD display, come in contact with it. Do NOT place pressure on the front of the unit at any time because the screen could crack. 1. Disconnect any cables or cords connected to the unit. 2. Lay the unit down on a flat surface, so the back side is facing up, making sure to place a soft cushioned material (such as a pillow or thick piece of foam) beneath the screen. 3. Remove the four screws and then remove the BASE STAND from the unit. PLV1615CS1- E1-23.pmd 14 20/04/2007, 15:36 USING HEADPHONES • Turn down the volume before connecting headphones to the unit, then adjust the volume to your desired level. • When headphones are connected, no sound will come from the front speakers. Note: • Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to you and may cause hearing loss. UNIT OPERATION Earphones / Headphones (1/8” [3.5mm] diameter plug) TURNING THE UNIT ON FOR THE FIRST TIME The first time for you turning on the unit, the unit will enter Virgin mode. You can easily follow up prompt message on screen to finish basic settings of the system. 1. Press the ENTER button to proceed the Initial Setup. 2. Use the / button to select your OSD language, and press the button to the next step. 3. Use the / button to select your TV tuner source (Antenna or Cable), and press the button to the next step. 4. Make sure RF aerial has been connected properly to TV ANTENNA input jack on the rear of the system, press the ENTER or button. The system will automatically start to scan and preset all available TV channels. 5. After scaning finished, “Inital setup is Complete.” will appear on the screen. Press the ENTER button to finish Initial Setup. After finishing above settings, the system will return to the first TV channel scaned just now. Note: When the unit is not going to be used for a long time, disconnect the AC power cord from AC power outlet. 15 PLV1615CS1- E1-23.pmd 15 20/04/2007, 15:36 16 TV SETUP VIDEO MENU 1. Press the MENU button. 2. Press the ENTER or button to select Video. 3. Use the or button to select the options (Picture Mode, Brightness, Contrast, Saturation, Tint, Sharpness or Color Temperature). Adjust them using the or button (The screen will change to your desired setting); or press the ENTER or button to go into the detailed settings. 4. Press the EXIT button to return to the previous menu. 5. Repeat steps 3 and 4 to adjust o...