Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Briggs & Stratton Dateigröße: 1.25 mb Dateiname: Unterrichtssprache:

Do not over-fill. Use a high quality detergent oil classified “For Service SC, SD, SE, SF, SG,” such as Briggs & Stratton “warranty certified” SAE 30 oil, part no. 100005. Use no'special additives with recommended oils. Do not mix oil with gasoline. SAE Viscosity Grades * Air cooled engines run hotter than automotive engines. Use of multiviscosity oils (10W-30, etc.) above 40° F (4° C) will result in high oil consumption and possible engine damage. Check oil level more frequently if using these types of oils. ** SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to inadequate lubrication. Check oil level before starting engine. Add oil as shown below. FUEL This engine will operate satisfactorily using any automobile gasoline. Use clean, fresh, lead-free gasoline with a minimum of 77 octane. (Leaded gasoline may be used if it is commercially available, and if lead-free is not available.) Purchase fuel in quantity that can be used within 30 days. See STORAGE INSTRUCTIONS, page 9. Do not mix oil with gasoline. Note: We do not recommend using gasoline which contains alcohol, such as gasohol. If gasoline with alcohol is used, it must contain less than 10% Ethanol and must be removed from engine during storage. Do not use gasoline which contains Methanol. Fuel level Do not over-fill. Allow space in fuel tank for fuel expansion. Oil capacity is about 1-1/2 quarts (48 ounces or 1.4 liters) if engine is not equipped with oil filter. Oil capacity is about 1-3/4 quarts (56 ounces or 1.7 liters) if engine is equipped with oil filter. Note: Oil capacity will be greater if engine is equipped with optional remote oil filter. Start and run engine at idle for 30 seconds. Shut engine off. Wait 30 seconds and check oil level. Add oil to bring level to Full mark on dipstick, if required. Place engine level Remove dipstick Tighten dipstick Clean around oil fill Wipe with clean cloth Remove and check Oil level should be If oil is required, add Tighten dipstick at FULL mark slowly - recheck firmly before starting In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu of pre-recorded messages offering you engine maintenance information. Before Starting 1. Rotating Screen 2. Air Cleaner 3. Carburetor 4. Spark Plug Wire 5. Engine Model xxxxx Type xxxx XX Code xxxxxxxx 6. Blower Housing 7. Oil Fill/Dipstick 8. Fuel Filter 9. 12V Electric Starter 10. Crankshaft 11. Oil Drain Plug Tips to obtain best starting results Start lawn mower on hard surface or over previously cut grass. Start, store and fuel lawn mower in level position. A Do not use a pressurized starting fluid. Starting fluid is flammable. Severe engine damage or fire may occur. Slightly richer fuel mixture usually .mproves cold starting (below 40° F). See CARBURETOR ADJUSTMENTS, page 5. Cold weather starting hints 1. Use the correct oil for the starting temperature expected. 2. De-clutch all possible external loads. 3. Set speed control at part throttle position. 4. A warm battery has much more starting capacity than a cold battery. 5. Do not use gasoline left over from summer. Use fresh winter grade gasoline which has higher volatility to improve starting. OIL GARD® (optional) If engine is run low on oil, the OIL GARD® will either activate a warning device or stop the engine. Add oil to engine. Fill to FULL mark on dipstick. Read the operating instructions supplied by the equipment manufacturer to determine which way your engine is equipped. Oil pressure switch (optional on engines with oil filter) If engine is run low on oil, the pressure switch will either activate a warning device or stop the engine. (Read the operating instructions supplied by the equipment manufacturer to determine which way your engine is equipped.) Add oil to engine. Fill to FULL mark on dipstick. In the USA and Canada, a 24 hour hot line, 1-800-233-3723, has a menu^of pre-recorded messages offering you engine maintenance information. Starting & Stopping START ENGINE A ALWAYS KEEP HANDS AND FEET CLEAR OF MOWER BLADE OR OTHER ROTATING MACHINERY. Fuel shut-off valve Open fuel shut-off valve, if engine is so equipped. Throttle Move throttle control to RUN or FAST position. Choke Move choke control to CHOKE or START position. Note: Choke must fully close. If engine does not start, see Adjustments, page 5. Rewind starter Grasp rope handle as illustrated and pull slowly until resistance is felt. THEN PULL CORD RAPIDLYTO OVERCOME COMPRESSION, PREVENT KICKBACK AND START ENGINE. Repeat if necessary with choke off and throttle control in FAST position. When engine starts, operate in FAST position. Rope starter Âk, Wind starter rope around pulley in direction shown by arrow. Pull rope handle slowly until resistance is felt, then pull with a quick full arm stroke to prevent kickback. Repeat if necessary with choke opened slightly. When engine starts, open choke gradu...

Herunterladen

Geben Sie zwei Ziffern: