Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Toshiba Dateigröße: 1.17 mb Dateiname: Unterrichtssprache:

To cancel sleep time, press the SLEEP button repeatedly until the display turns to 0. 5. VOL (VOLUME) + / – Buttons -Press the + button to increase, or the – button to decrease the volume level. 6. MENU Button -Press to display the on-screen menu function. 7. SET + / – Buttons - Press to select the desired setting during on-screen operations. 8. RESET Button - Press to reset the on-screen picture adjustments to their factory preset positions. 9. TV/VIDEO Button -Switches between the TV and external device inputs. 10. RECALL Button -When you press this button, the channel number will appear in the upper right corner of the screen. Press the button again to remove it from the screen. 11. MUTE Button -To turn off the sound, press this button once. The TV will be silenced and the word “MUTE” will appear on the screen. The muting feature can be released by pressing the MUTE button again or one of the VOL + or – buttons. 12. CH (CHANNEL) + / – Buttons -Press the + button to change to a higher numbered channel set into memory. Press the – button to change to a lower numbered channel set into memory. 13. ENTER Button -Press to enter or select information for On-screen operations. 14. 1/2 Button -Switches between Channel 1 and Channel 2 in the Closed Caption mode. 15. CAP/TEXT Button -Press to switch between normal TV and the two Closed Caption modes (captions or text), when available. Before using the remote control, batteries must first be installed. HOW TO INSTALL BATTERIES 1. Open the battery compartment cover. 2. Install two “AAA” (penlight size) batteries. 3. Replace the battery compartment cover. Use two “AAA” size penlight batteries (supplied) for the remote control. The batteries may last approximately one year depending on how much the remote control is used. For best performance, it is recommended that batteries should be replaced on a yearly basis, or when the remote operation becomes erratic. BATTERY PRECAUTIONS These precautions should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the remote control will not be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer's directions.) ANTENNA/CATV CONNECTIONS Choose one of the following seven connections, based on your equipment and service: Combination VHF/UHF antenna Single 75 ohm cable (or) Single 300 ohm twin-lead wire* TRANSFORMER (not supplied) *For best performance, if you have a splitter connected, remove the splitter and connect the single wire to the transformer, and then to the TV’s antenna input (as illustrated here). To ANT inputon back of TV To ANT inputon back of TV Separate VHF and UHF antennas or Combination VHF/UHF antenna with separate cables/wires 300 ohm twin-lead wire COMBINER (not supplied) UHF Antenna VHF Antenna 75 ohm cable 300 ohm twin-lead wire COMBINER (not supplied) UHF Antenna VHF Antenna 300 ohm twin-lead wire* TRANSFORMER (not supplied) To ANT input on back of TV To ANT input on back of TV (or) A B Cable TV service (or) (or) To ANT input on back of TV To ANT input on back of TV To ANT input on back of TV From cable TV service From cable TV service From cable TV service A / B SWITCHSPLITTER CONVERTER/ DESCRAMBLER CONVERTER/ DESCRAMBLER Combination VHF/UHF Antenna (Single 75 ohm cable or 300ohm twin-lead wire) Connect the 75 ohm cable from a combination VHF/UHF antenna to the antenna jack. If your combination antenna has a 300 ohm twin-lead wire, use the 300-75 ohm matching transformer (not supplied). Combination VHF/UHF Antenna (Separate VHF and UHF 300ohm twin-leads) Connect the UHF twin-lead wire to a combiner (not supplied). Connect the VHF twin-lead to the 300-75 ohm matching transformer (not supplied). Attach the transformer to the combiner. Attach the combiner to the antenna jack. Separate VHF/UHF Antennas Connect the 75 ohm cable from the VHF antenna and the UHF antenna twin-lead to a combiner (not supplied). Attach the combiner to the antenna jack. NOTE: If your VHF antenna has a twin-lead wire, use the 300-75 ohm matching transformer (not supplied), then connect the transformer to the combiner. For Subscribers to Basic Cable TV Service For basic cable service not requiring a converter/descrambler box, connect the CATV 75 ohm coaxial cable directly to the antenna jack on the back of the television. For Subscribers to Scrambled Cable TV Service If you subscribe to a cable service which requires the use of a converter/descrambler box, connect the incoming cable to the converter/descrambler box and conn...

Herunterladen

Geben Sie zwei Ziffern: