Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Samsung Dateigröße: 3.84 mb Dateiname: Unterrichtssprache:

Depending on the material of the floor, it may get scratched when the unit is moved. Care should be taken when moving the unit. • When you want to install the Projection Television in a given location, or use it on the carpet, make sure to use the accompanying caster trays (4 units). When placing the caster tray beneath the casters, be sure your fingers do not get caught. 1.1 CHAPTER ONE: YOUR NEW TV YOUR NEW TV Familiarizing Yourself with The TV Front Panel Buttons The buttons on the front panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control. Ў HCL552W HCL652W HCL5515W HCL6515W Ў HCL4715W Ў HCL473W HCM5525W HCM553W HCM6525W HCM653W OE TV/VIDEO Press this button to display a menu of all the available signal sources. When the menu appears, use the Joystick up or down to highlight a particular source, and then move the joystick to the right to select it. . MENU Press to see an on-screen menu of your TV's features. . VOL – , + Press to increase or decrease the volume. Also used to select items on the on-screen menu. . CHЎand CH^ Press to change channels. Also press to highlight various items on the on-screen menu. . OPEN/CLOSE (HCL552W / HCL652W / HCL5515W / HCL6515W) Press to open and close the front panel door. . MUTE (HCL4715W/HCL473W/HCM5525W/ HCM553W/HCM6525W/HCM653W) Press to temporarily cut off the sound. ” Remote Control Sensor (HCL4715W/HCL473W/HCM5525W/ HCM553W/HCM6525W/HCM653W) Aim the remote control towards this spot on the TV. ’ Timer indicator (HCL4715W/HCL473W/HCM5525W/ HCM553W/HCM6525W/HCM653W) When the TV is turned on, the Timer indicator blinks about ten times. This indicator illuminates when the Timer mode is set to the “On” position after setting the clock and either the On timer or Off timer, with the remote control. Even if the power is turned off, this indicator stays lit. (Clock must be set before using this function.) CHAPTER ONE: YOUR NEW TV 1.2 O POWER Press to turn the TV on and off. 1.3 CHAPTER ONE: YOUR NEW TV YOUR NEW TV OE S-VIDEO INPUT jack Use to connect an S-Video signal from a camcorder or a video game. . VIDEO INPUT jack Use to connect a video signal from a camcorder or a video game. . AUDIO INPUT jacks Use to connect the audio signals from a camcorder or video game. . PERFECT FOCUS (HCL4715W/HCL473W/HCM5525W/ HCM553W/HCM6525W/HCM653W) Press to adjust for the optimum picture set in the Factory. Front or Side Panel Jacks You can use the front or side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment, see pages 2.1 – 2.8.) Using a display deck (HCL473W/HCM5525W/HCM553W/ HCM6525W/HCM653W) You can display a VCR, a DVD player, etc. by using the display deck. ^HCL552W/HCL652W/HCL5515W/ HCL6515W ^HCL4715W ^HCL473W/HCM5525W/ HCM553W/HCM6525W/ HCM653W 1 Press the symbol “ “ at the center of the display deck. 2 As shown in figure below, hold the center of door and lift it in the direction of arrow till a ‘ttok’ sound sounds. 3 After displaying a component you have in the display deck, hold the center of door and pull it down as shown in figure below 4 Shut the door by pressing the symbol “ “. . Note: You should display only the component that is within 126mm high. When displaying a component in the display deck, please space it out 30mm from the front, 20mm from either end. CHAPTER ONE: YOUR NEW TV 1.4 YOUR NEW TV Rear Panel Jacks Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player. Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.) For more information on connecting equipment, see pages 2.1 – 2.8. OE ANTENNA terminals Two independent cables or antennas can be connected to these terminals. Use ANT-A and ANT-B terminals to receive a signal from VHF/UHF antennas or your cable system. Use the ANT-A OUT terminal to send the signal being received by the ANT-A terminal out to another component (such as a Cable Set Top Box). The PIP channel can be received only when a signal source is connected to ANT-A. . S-VIDEO INPUT jack Connect to an S-VHS VCR or DVD player. . VIDEO INPUT jacks Connect to the video output jacks of VCRs, DVD players and similar devices (Two sets are available: Video1 and Video2). . AUDIO INPUT jacks Connect to the audio output jacks of VCRs, DVD players and similar devices. . AUDIO-VIDEO MONITOR OUTPUT jacks Connect to the audio/video input jacks of a recording VCR. Note: The monitor out does not operate in DVD or DTV mode. O COMPONENT 1(480i, 480p) INPUT jacks Connect a source that outputs 480i/480p Y,PB and PR signals, such as a DVD Player. . COMPONENT 2(480p, 1080i) INPUT jacks Connect a source that outputs 480p/1080i Y,PB and PR signals, such as a DTV Set-Top Box. ” SURROUND OUT (HCL552W/HCL652W/HCL473W/ HCM553W/HCM653W only) Connects to a (option...

Herunterladen

Geben Sie zwei Ziffern: