Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Philips Dateigröße: 257.04 kb Dateiname: 265cb7e9-a3d9-46b0-b562-0b442b75634e.pdf Unterrichtssprache:

Never use aggressive cleaning agents. Use a slight damp chamois leather. • there is a lightning storm. • the set is left unattended for an extended period of time. CAUTION: Never attempt to repair a defective TV yourself. Always consult a skilled service personnel. Switch off your TV overnight via the POWER ON/OFF button instead of leaving it on stand-by. You save energy and at the same time demagnetise the picture tube. A demagnetised picture tube supports good picture quality .When the set is switched on, do not shift, move or turn (e.g. on a swivel base) the set around because an uneveness in colour in some parts of the screen may occur.This can be eliminated by switching off the set by the mains power button . Wait for 20 minutes before switching on again. If symptom still exists, call for service. Before Calling For Service Please make these simple checks before calling for service. SYMPTOM CHECK/ACTION Colour patch (uneveness) • Switch off TV by the mains power button. Wait for 20 minutes before switching on again. No power • Check TV's AC power cord is plugged into mains socket. If there is still no power, disconnect plug. Wait for 60 seconds and re-insert plug. Switch on TV again. No picture • Check antenna connection at rear of the TV. • Possible faulty TV station. Try another channel. • Increase the contrast setting first and then the brightness setting. Good picture but no sound • Try increasing the volume. • Check sound is switched on. Good sound but poor or abnormal colour or no picture • Increase the contrast setting first and then the brightness setting. Snowish picture and noise • Check antenna connection at rear of the TV. Horizontal dotted lines • Possible electrical interference! e.g. hairdryer.nearby neon lights, etc). Switch off equipment. 'Ghosts' or double image • Possible poor positioning of antenna. Using a highly directional antenna may improve reception. One white line across the screen • Switch off set immediately and consult service personnel. TV not responding to remote control handset • Check life span of batteries. • Aim remote control handset directly at remote control sensor lens on the TV set. 2 Safety Information Positioning of the TV • Place TV set on a solid base (e.g. a TV/Video cabinet) • Leave at least 3 cm around each side of TV set for ventilation to avoid over-heating. • Do not place TV set near a radiator or other sources of heat. • Do not place TV set where it can be exposed to rain or excessive moisture. Power Connection • For correct mains voltage, refer to Specification page. • Consult your dealer if mains supply is different. NOTE: This plug is not representative of the actual plug and socket. Care of Remote Control handset • Always remove the batteries from the remote control handset if handset is not used for a long period. This can help prevent damage to handset from possible battery leakage. 3 English English PRE-INSTALLATION ANTENNA CONNECTION • For indoor antenna, attach it to the mounting socket of the backcover. • Connect aerial plug to the antenna socket t on the backcover. • For external antenna, connect the aerial plug to the antenna socket t on the backcover. PERIPHERAL EQUIPMENT CONNECTION • Connect antenna to Antenna RF Input of VCR. • Connect RF cable from RF Output of VCR to the Antenna InputT of the TV. AV SOCKETS (backcover) Connect the VIDEO in and AUDIO in sockets of the TV to the VIDEO out and AUDIO out sockets of the VCR for playback programmes. (Applicable to sets with AV mode only) 4 NAME AND FUNCTION OF CONTROLS ®---U---© FUNCTIONS OF TV © Main Power button Turns main power on and off. © Headphone socket Connects headphone jack to socket for personal listening. (Applicable for certain models/versions only) © Volume Down button Adjusts sound volume softer. © Volume Up button Adjusts sound volume louder. © Channel Down button Selects channel backward. © Channel Up button Selects channel forward. © Stand-by light indicator Indicates red light when stand-by is on. © Remote Sensor Aim remote control here. 5 English NAME AND FUNCTION OF CONTROLS FUNCTIONS OF REMOTE CONTROL PHILIPS d>— & d> 2 3—I CD CD 5 6 ^ I—11—iH-h£> 7 8 9 I □ QOj c>l> OSD I 0 |A/CH CD CD[CDjCD- © Stand-by button Turns TV on and off when main power is on. © Channel Up/Down button Selects channels preset on programme number. © Volume Up/Down button Adjusts sound volume louder or softer. © Digit (0 - 9) button Selects channel directly. Press desired number to select(one digit). For two-digit channel number, press the first digit followed by the second digit. © Alternate channel button Alternates last viewed channel and present channel. © On Screen Display button Displays channel number and sleep-timer. © Install button Starts installation menu and store new settings. © Menu and Menu Up/Down button Selects and start the various menu. © Mute button Mutes sound temporarily. On-Timer button Not ...

Herunterladen

Geben Sie zwei Ziffern: