Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Be sure to use the center of each stud. (these marks should line up with the ones made in step 3 above using the template). 6 Set the mount aside and drill a 1/4” (6 mm) pilot hole at each marked location. 7 Place the mount back against the wall and secure it using the lag bolts (Q) and lag bolt washers (R) provided. Do not over-tighten these bolts and do not release the mount until all bolts are in place. 8 Once all (4) lag bolts are in place you must tighten each one. (note: be sure not to over tighten). 1 1 3.2 Mounting the wall plate (concrete) B Warning For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and display. 1 See enclosed mounting template for diagram and use enclosed mounting template as a guide for precision mounting. 2 Using the enclosed mounting template, place the diagram against the wall and mark six locations on the wall where the mount Is to be Installed. 3 With the help of another person, place the mount against the wall and level it using the bubble guide. 4 While another person holds the mount in place, mark six locations on the wall where the mount is to be installed. 5 Set the mount aside and drill a 3/8” (10 mm) pilot hole at each marked location. Remove any excess dust from the holes. 6 Insert a concrete anchor (P) into each hole so that it is flush with the concrete surface. A hammer can be used to lightly tap the anchors into place if necessary. 7 Place the mount back against the wall and secure it using the lag bolts (Q) and lag bolt washers (R) provided. Do not over-tighten these bolts and do not release the mount until all bolts are in place. 2 2 Once all (6) lag bolts are in place you must tighten each one. Be sure not to over tighten. D Note If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface. 3.3 Attaching the arms to the display B Warning Use extra care during this part of the installation.Avoid laying your display face down if possible as it may damage the viewing surface. 1 Examine the back of your television. If the back of your display is flat: You will be using one of the shorter bolts from the hardware kit. 3 3 If the back of your display is curved or recessed: You will be using one of the longer bolts and a spacer. 4 2 4 Determine the correct diameter bolt to use by trying one bolt each from Bags 1 - 4 of the hardware kit. Do not force any of the bolts – if you feel resistance stop immediately to avoid damaging your display. 3 Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the corresponding lock washer (C, F, I, or L).You will need to use the M6 washers (O) if you are using the M4, M5, or M6 bolts. If your display has a curved or recessed back, you may also need to use a spacer (M or N). 4 Make sure the screws are snug, but do not over-tighten. 5 5 ETip Use a longer bolt and spacer for displays with curved or recessed backs. Do not use the M6 washer (O) if you are using the M8 bolts (J or K). 4 Mounting and adjusting 1 With the help of another person, carefully lift your display and place it on the wall plate. Do not release the display until the mounting arms have securely hooked onto the mount. 6 6 2 Carefully hook the display onto the wall plate 7 7 B Warning Insert the safety bar at the center of the mount to avoid having the display accidentally knocked off the mount. 3 This MUST be done in order to secure the display to the mount. NOTE:A cotter pin (included) Is used to secure the arms to the mount OR a padlock (not included) can be inserted into the hole at the end of the saftey bar to help prevent theft of your display. A small cotter pin can be used to secure your display to the mount. (included) 8 8 Once the tv is fitted properly on to the wall bracket, the security bar must be put into place. 8 D Note Slide arm through slots in wall plate & brackets Once the security bar is slid into the appropriate slots, a lock(not provided) may be placed for additional security. 6 A small cotter pint can be used to secure 9 replacement of the product. Incidental, special and consequential damages are disclaimed where permitted by law.This warranty gives you specic legal rights.You may also have other rights that vary from state to state. Register your product and get support at 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount. Call 1-919-573-7854. Limited Two-Year Warranty Philips warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specications and warnings, for two years from the date of your purchase of this product. This warranty extends only to the original purchaser of the product, and is not transferable. To exercise your rights under this warranty, you must provide proof of...