Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1 • For safety, install the set in a position at which the driver cannot see it. • Do not disassemble or modify the set. Doing so may damage it and voids your warranty. • Keep drinks and drops from umbrellas away from the set. Water may damage the internal circuitry. • Do not let the set become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. (The liquid crystal panel will work properly within a temperature range of 30 – 113 degrees F.) • In extremely cold temperatures, the movement of the picture may be slow and the picture may be dark, but this is not a malfunction. The set will work normally once the temperature increases. • Small black and shiny dots inside the liquid crystal panel are normal for liquid crystal products. PACKAGE CONTENTS The Clarion VMA1041 comes with the following items: • Ribbon Cable for connection to the TTX001 TV Tuner • A/V RCA Cable • Power Cord • Table Top Stand BUTTON LOCATIONS 4 Mode Selection Button 5 Power Button 6 IR Remote Sensor 1 Volume Down Button 2 Volume Up Button 3 Picture Adjustment Button 2 7 DC Power Connector 8 Earphone Jack 9 AV2 Input Connectors 0 AV1 Input Connectors q VGAInput Connector t TV Tuner Ribbon Connector w Channel Preset Button y TTX001 TV Tuner (optional) e Channel Down Button u Antenna Input Connector r Channel Up Button 3 INSTALLATION AND WIRING Before You Begin: 1. This monitor is exclusively for use in cars with a 12V negative ground power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery’s negative terminal before starting. This is to prevent short circuits during installation. NOTE: The VMA1041 cannot be used by itself. It should be connected to a device such as a Clarion TTX001 TV Tuner or a source such as a video cassette player. Wiring 1. Be sure to turn the power off before wiring. 2. Be very careful where you route the wires. Keep them well away from the engine, exhaust pipe, etc. Heat may damage the wires. 3. If the fuse should blow, check to see if the wiring is correct. 4. Fasten the ground lead (black) securely to a clean chassis ground. If the unit is insufficiently grounded, it may not operate or there may be noise. Power 1. Connect the output of the DC-Adapter on the DC-Input port. 2. Connect one end of the power cord to DC-Adapter socket and connect the other end of the cord to the power supply. 3. Connect the PC-VGA cable to the VGA port for computer application. 4. Connect A/V cables to AV1 and AV2 port for auxiliary video application. PICTURE ADJUSTMENT To adjust from the unit: 1. Press the Picture Adjustment button until the desired adjustment appears on the screen. The picture control symbols will appear on the screen in the following order: CONTRAST BRIGHT TINT COLOR H-CENTER VCENTER 2. Press the Volume +/- buttons to adjust the selected function. To adjust from the remote control: 1. Press the Picture Select button on the remote control until the desired adjustment appears on the screen. The picture control symbol will appear on the screen in the following order: CONTRAST BRIGHT TINT COLOR H-CENTER V-CENTER 2. Press the Channel +/- button to adjust the selected function. To adjust the viewing angle: 1. Gently hold both sides of the cabinet and tilt the monitor up or down to achieve the desired viewing angle. 2. The recommended viewing is +30 degrees to –10 degrees vertical and +45 degrees to –45 degrees horizontal. 4 AUXILIARY VIDEO INPUTS OPERATION The VMA1041 is equipped with two auxiliary A/V Inputs. 1. Plug the AV1 Audio/Video Input cord into the AV1 and/or AV2 input jacks. 2. Connect Audio/Video Connectors to the Auxiliary Source. 3. Press the Input Selection button on the unit or remote control until VIDEO 1 or VIDEO 2 is displayed. 4. The selected auxiliary video source should be seen. OPTIONAL REMOTE CONTROL BATTERY INSTALLATION • Insert 2 AAA batteries into the compartment located on the back of the unit, observing the proper polarity. NOTES: • Each time you change the batteries, you must reprogram the channels. • We suggest you use alkaline batteries; do not use rechargeable batteries. • Always change all the batteries at the same time. 5 OPTIONAL REMOTE CONTROL OPERATION • To use the remote control, press the Power button to turn on the remote. • Press the TV/VIDEO button to select the source to be controlled by the remote. • The VOL(ume) +/- buttons and the MUTE button control the TV volume. 1 Number Pad 2 Skip 3 Erase/Write 4 Volume Up 5 Volume Down 6 TV/Video 7 Power 8 Channel Up 9 Mute 0 Channel Down q Picture Select w Auto Memory e TV/CATV OPTIONAL TTX001 TV TUNER INSTALLATION • Slide the TTX001 onto the back of the VMA1041. • Install the screws provided, as shown in the illustration below. • Insert ribbon cable into ribbon cable connector. • Connect external antenna to antenna input connector. Note: When using a TV Tuner with the VMA1041, AV1 Input Connector will be d i s a b l e d . 6 T...