Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Mitsubishi Electronics Dateigröße: 1.35 mb Dateiname: projector_manual_3172.pdf Unterrichtssprache:

It may cause the product to fall and could cause injuries. Before installing, check whether the material of wall satisfies the specifications and make sure to use enclosed anchors supplied with the product. Otherwise it may cause safety problem. Do not place a heat source (radiator or heater) or a humidifier under the installed product. It may cause a fire or could give an electric shock. When drilling use drill and drill bit specified by the manufacturer. And the depth of the hole should satisfy the specifications. Otherwise it may cause safety problem. Do not install this product near a sprinkler, a sensor, a high voltage electric line, any power source or the place where impact or vibration can affect. Unplug the product before installing. Do not install this product barehanded. Otherwise it may cause a fire or could give an electric It may cause injuries. shock. Installing and Composition Accessories for wall mounting bracket Wall mounting bracket Bolts for wall mounting Wall anchor bolt Bolts for fixing the Fixing fixers Bolts for using the bracket sleeves bracket wood Installing Wall mounting bracket 1 Detach the products -Detach bolt from wall mounting bracket. - Detach product fixing bracket from Wall mounting bracket. Wall mounting bracket Product fixing bracket Bracket fixing bolt * After inserting the projector, you use this bolt.(Refer to p.18) . Press the upper of the wall bracket with both hands to tilt the bracket. It’s convenient when joining the fixing bolt.(Refer to p.18) 2 Assemble projector with the product fixing bracket a. Carefully place the lens side down on a cushioned surface that will protect the lens from damage. b. Insert the 2 fixing fixers on the top of the projector.(It’s top that the point of auto ventilation door.) c. Insert the product brackets detached in the fig.1 on the projector with bracket fixing bolts. Bracket fixing boltFixing fixer Installing and Composition 3 Insert anchors or bolts for using the wood after marking the positions where products are mounted on the wall O Check the surface or thickness that the wall mounting bracket. O When the surface that the wall mounting bracket is concrete, strong , weak natural rock, brick and hollow block, you can use the supplied anchors or bolts. O Only thickness of strike off material is less than 20mm, you can use the supplied anchors or bolts. O Only making wood into wall, you can use the supplied bolts for using the wood. O Plasterboard is not a sufficiently strong enough material. Using the wall anchor bolt sleeves and bolts for wall mounting bracket a. After matching the positions of the wall bracket, mark the positions of the anchor. b. At the position of anchor marked in the wall, using on 6mm drill appropriate for the material on the wall, drill each hole to a depth of above 40~50mm. c. Clean each drilled hole and insert an anchor supplied with the wall mounting bracket into each hole. a b c Drill Wall Anchor . : Anchors insertion position Installing and Composition 4 Install the wall mounting bracket on the wall Using the wall anchor bolt sleeves and bolts for wall mounting bracket a. Mount the wall mounting bracket on the wall as setting the hole. b. Insert the bolts for wall mounting bracket as setting the each hole. a b Bolt for wall mounting bracket Using the bolts for using the wood O Only making wood into wall, you can use. -After matching the position of the wall, mount the wall mounting bracket using the bolts for using the wood supplied. Installing and Composition 5 Assemble the projector with the wall mounting bracket O Assemble a projector with the wall mounting bracket installed on the wall as below Fig. Do not install this product by yourself. Get some help from others. It may cause the product to fall and could cause injuries. a. Hang fixing 2 fixers on a upper groove. b. Insert the product bracket to the groove of the lower wall mounting bracket. c. After assembling and fixing the projector, insert the bolts for fixing bracket to the hole. d. Entirely check the projector fixed as pulling the lower projector. Fixing fixer Product bracket Bolt for fixing the bracket a b c Installing and Composition Adjusting Tilt Angle -Adjustable angle range is 5°(upside/downside/left/right) and turn range is ±10. -Do not adjust tilt angle with too much force. It may cause damage of product or could cause injuries. Adequate installation space from the wall -Leave 16.8 mm between the projector and the wall when installing the wall bracket on the wall. 16.8mm Installing and Composition Turning on the Projector 1. Connect power cord correctly. 2. Press the POWER button on the remote control or top cover. (Green operation indicator flashes during cooling of the lamp.) When projector is turned on, auto sliding door and shutter are opened, automatically. It will take about 25 second to display the picture after power on because the projector lamp has to warm up. An image will appear after t...

Herunterladen

Geben Sie zwei Ziffern: