Stimmen - 6, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
3. When all digits are entered and the password is ready, press Auto to confirm. A confirmation message displays. Password Setup Enter Password Press Auto to Confirm Press 5 or 6 to change number Press 3 or 4to move 0000 • The password will display on-screen when being input. • IMPORTANT: Write your selected password down here in this manual so that it is available to you should you ever forget it. Password: __ __ __ __ Keep this manual in a safe place. 4. Perform one of the following 3 steps. i. Press Auto to continue. The set-up is finished when the message “Password setup completed” displays. ii. Press Up 5 to go back to the previous screen and re-enter four digits. iii. Press Down 6 to cancel the password set-up and return to the on-screen menu. Password Setup Do you want to use 0 0 0 0 as your password? Yes Auto No 5 Cancel 6 If you forget the password You will be asked to enter the four digit password every time you turn on the projector. If you enter the wrong password, the password error message displays. You can retry by turning off the projector (by pressing Power) and start again, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. To enter the password recall procedure Press and hold Right4 for 5 seconds. The projector will display a coded number on the screen. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. To change the password 1. Open the on-screen menu and go to Setting > Change Password. 2. Press Left 3 or Right4. A “Password Change” message displays. 3. Enter the old password. i. If the password is correct, you can go on to enter new password. IMPORTANT: Write your selected password down here in this manual so that it is available to you should you ever forget it. Password: __ __ __ __ Keep this manual in a safe place. ii. If the password is incorrect, a “Password Error” message displays. Press Up 5 to try again or press Down 6 to cancel. 22 Operation Operation 23 4. Check the new password. i. Pressing Auto completes the procedure. ii. Press Up 5 to try again. iii. Press Down 6 to cancel the set-up and return to the on-screen menu. Adjusting the height The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Lift the projector up and press the adjuster button to release the adjuster. The adjuster will drop into position and be locked. Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes. 2. Screw the rear adjuster foot to fine tune the horizontal angle. To retract the foot, hold up the projector while pressing the front adjuster button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction. If the screen and the projector are not perpendicular to each other, the projected image becomes vertically trapezoidal. To correct this situation, adjust the value of Keystone in the Picture menu, on the projector control panel, or on the remote control. Auto-adjusting the image In some cases, you may need to optimize the picture quality. To do this, press Auto on the control panel of the projector or on the remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. The current source information will be displayed at the bottom right of the screen for 3 seconds. The screen will be blank while Auto is functioning. Fine-tuning the image size and clarity 1. Adjust the projected image to the size that you need using the zoom ring. 2. Then sharpen the image by rotating the focus ring. Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following ONE of these steps. 1. Press 3 Left/ Right 4 on the control panel of the projector to display the status bar labelled Keystone. Press Left 3to correct keystoning at the top of the image. Press Right4 to correct keystoning at the bottom of the image. 2. Press / on the remote control to display the status bar labelled Keystone, then press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image. 3. Press 6 Menu on the projector or Menu on the remote control. Go to Picture --> Keystone and adjust the values by pressing Left 3/ Right 4 on the projector or Left 3/ Right 4on the remote control. For example, 1. Press Left 3 on the projector or 2. Press on the remote control or 3. Press Left 3on the projector or 3 on the remote control when you are in Pi...