Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Port of the projector with the 2 When the computer is switched on first, the Wireless Mouse may Control Cable for Serial Port. not work properly. OPERATING WIRELESS MOUSE When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on the Wireless Remote Control Unit. POINT button POINT button (Move the pointer) Used to move the pointer. The pointer is moved corresponding with the direction you are pressing. SELECT (LEFT CLICK) button This button has the same function as the left button in a PC mouse. RIGHT CLICK button This button has the same function as the right button in a PC mouse. Pressing this button does not affect any operation when in Menu SELECT button RIGHT CLICK button mode. (left button of the (right button of the mouse) mouse) APPENDIX MAINTENANCE TEMPERATURE WARNING INDICATOR (Small) (Large) The TEMPERATURE WARNING Indicator flashes red when the internal temperature of the projector exceeds the normal temperature. The Indicator stops flashing when the temperature of the projector returns to normal. When the TEMPERATURE WARNING Indicator continues to flash, check the items listed below. 1 1 The Ventilation slots of the projector may be blocked. In such an event, reposition the projector so that the ventilation slots are not obstructed. 2 2 Air filters may be clogged with dust particles. Clean the air filters by following the section AIR FILTER CARE AND CLEANING below. 3 3 If the TEMPERATURE WARNING Indicator remains on after performing the above checks, the Cooling Fans or the Internal Circuits may be malfunctioning. Contact service a personnel from an authorized dealer or service station. AIR FILTER CARE AND CLEANING The Removable Air Filters prevent dust from accumulating on the surface of the Projection Lens and the Projection Mirror. Should the Air Filters become clogged with dust particles, it will reduce the Cooling Fans' effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the Air Filters following the steps below: 1 1 Turn the power off, and disconnect the AC power cord from the AIR FILTER AIR FILTER AC outlet. 2 2 Turn the projector upside down and remove two Air Filters (Large and Small) by pulling the latches upward. 3 3 Clean the Air Filters with brush or wash out the dust and particles. 4 4 Replace each Air Filter properly. Make sure that the Air Filters are fully inserted. CAUTION Do not operate the projector with the Air Filter removed. Dust may accumulate on the LCD Panel and the Mirror degrading picture quality. Do not put small parts into the Air Intake Vents. It may result in malfunction of the projector. The Air Filter is a small part. Ensure that children don’t eat or swallow it. RECOMMENDATION We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments may cause poor image quality. When using under dusty or smoky conditions, dust may accumulate on the liquid crystal panel, lens, or optical elements inside it. This condition may degrade the quality of the projected image. When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING THE PROJECTION LENS Follow these steps to clean the projection lens: 1 1 Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 2 Lightly wipe the cleaning cloth over the lens. 3 3 When the projector is not in use, replace the lens cover. APPENDIX LAMP REPLACEMENT When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required. CAUTION For continued safety, replace with a lamp assembly of the same type. Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot. Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury. 1 1 Follow these steps to replace the lamp assembly. Turn off the projector and disconnect the AC plug. Allow the 2 2 projector to cool for at least 45 minutes. Remove the screw with a screwdriver and remove the Lamp 3 3 Cover. Remove the two screws with a screwdriver and pull out the 4 4 Lamp Assembly by grasping the handle. Replace the Lamp Assembly with a new one and tighten the two screws. Make sure that the Lamp Assembly is set properly. Replace the Lamp Cover and tighten the screw. 5 5 Connect the AC Power Cord to the projector and turn the 6 6 projector on. Reset the Lamp Replacement Monitor Timer (refer to the section “Lamp Replacement Monitor Timer” below). NOTE : Do not reset the LAMP REPLACEMENT MONITOR TIMER when the lamp is not replaced. ORDER REPLACEMENT LAMP Replacement Lamp can be ordered t...
Dieses Handbuch ist für folgende Modelle:Fernseher - LC-XM1 (421.16 kb)