Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Palsonic
Dateigröße: 829.34 kb
Dateiname: 0d7005a3-e9eb-4e3d-9b1a-6648496ce071.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Don't try to push anything into the cabinet or place any vessel with water on the TV set. Don't overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 3 Identification of Controls Front Power Switch Remote sensor MENU TV/AV Channel up/down Volume up/down Back AV2 input (VIDEO, AUDIO: L/MONO, R) DVD input (VIDEO; Y,Cb,Cr, AV output AUDIO; L/MONO, R) (VIDEO, AUDIO; L, R) AV1 input (VIDEO, Antenna input AUDIO; L/MONO, R) S-VIDEO input 4 Identification of Controls Remote control Power on/Standby Direct channel select Digit select Sleep timer Program scan Enter into music mode Volume down Open the menu 5 321 7 98 64 0 TV/AV ZOOM GAME CALL MUTE SCAN MUSIC TV/VIDEO input select Game playing Picture zoom Recall on-screen display Sound mute Return to previous channel Picture mode select Lock setting Access picture menu Select higher program Volume up Select lower program 5 Antenna connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. TV REAR Notes: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. 6 Preparing the remote control Installing batteries Effective range of the Remote Notes: Install two "AA" batteries matching the +/-polarities of the battery to the +/marks inside the battery compartment. Open the battery cover. Replace the battery cover. 5 321 7 98 64 0 TV/AV ZOOM GAME CALL MUTE SCAN MUSIC Notes: When there is an obstacle between the TV and the transmitter, the transmitter may not operate. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV the remote operation may be unstable. Do not try to recharge batteries that are not intended to be recharged. Use only the size and type of batteries specified. Do not mix different types of batteries together or old batteries with fresh ones. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. Do not throw the batteries into a fire. Dispose of used batteries in the specified manner. Do not drop, dampen or disassemble the remote control. 7 External equipment connections The following describes how to use and connect the TV with other AV equipment (for example, VTR, Video Camera, DVD, Video game, etc.) Please refer to the owner's manual of the equipment to be connected as well. To connect AV input terminals Connect side AV inputs To access the unit connected to these jacks, press TV/AV button until AV2 appears on the screen. TV SET SIDE Yellow (video) White (audio L/MONO) Red (audio R) Video game WY R To video outputs W Y R W Y R To audio outputs Signal Connect rear AV inputs If your video equipment has a S-VIDEO output terminal, connect it to the S-VIDEO input terminal on the unit. If not, connect it to the VIDEO terminal (RCA ). The S-VIDEO and AV1 use the same group of audio input terminals. VTR without VTR without S-VIDEO terminal W Y R S-VIDEO terminal : Yellow (video) : White (audio L/MONO) : Red (audio R) To audio outputs To video output TV SET REAR To audio outputs To S-VIDEO output terminal WYY R W YY R WR W R To access the unit connected to these jacks, press TV/AV button until AV1 or SVHS appears on the screen. 8 External equipment connections To connect DVD input terminals The figure below shows how to connect the DVD input terminals of the TV set to the DVD Player, Laser Disk Player, etc. The TV set rear DVD Player, Laser Disk Player etc. :Direction of the signal :White (audio L/MONO) :Red (audio R, CR) :Green (Y) :Blue (CB) G B W R Signals Y CB CR R L To access the unit connected to these jacks, press TV/AV button until YUV appears on the screen. Notes: 1. Both the CR terminal and the audio R terminal are red for easy identification. Make sure they are correctly connected. 2. DVD and AV1 use the same group of audio input terminals. To connect the AV Outputs You can connect an audio system to the AV output jacks on the TV set rear to enjoy a high-quality sound from the audio system, or you can connect the AV output jacks to the VTR to record the program you like. To external input Audio System Yellow (video) white (audio L) red (audio R) Another VTR for recording The TV set rear W Y R Signal W Y R W Y R Signal To video input To audio inputs 9 Power on/off 5 321 7 98 64 0 TV/AV ZOOM GAME CALL MUTE SCAN MUSIC Turning on 1 Press the Power Switch on the TV set. If no picture appears on the screen and the standby indicator ...