Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Portable Oxy-Fuel Welding and QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 TM BUILT TO LAST Cutting Outfit Unpacking When unpacking, inspect carefully for any damage that may have occurred during transit. Report any missing or damaged items by calling (800) 746-5641. Become

This warranty extends to the Welder, the Welders Transformer and Rectifier, Welding Gun or Electrode holder, and cables only. 5. WHAT IS NOT COVERED UNDER THIS WARRANTY: A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS WARRANTY. After this period, all risks of loss, from whatever reason, shall be on the purchaser. Some States do not allow limitation on how long an implied warranty lasts, so the above limitation

Electrodes used for shielded metal arc welding have two parts. The inner core is a metal rod or wire that should be similar in composition to the base metal. The outer coating is called flux. Various types of flux exist. Each coating is used for a particular welding situation. While the metal is molten, it can be contaminated by elements in the air. This contamination could weaken the weld. The flux coating creates a protective barrier called slag that protects the molten metal from contaminants

When the speed is to slow, the weld metal piles up and the bead is high and wide. SlAG ReMOVAl Wear ANSI approved safety glasses (ANSI Standard Z87.1) and protective clothing when removing slag. Hot, flying debris can cause personal injury to anyone in the area. After completing the weld, wait for the welded sections to cool. A protective coating called slag now covers the weld bead which prevents contaminants in the air from reacting with the molten metal. Once the weld cools to the point that

5. Hold wire and cut the wire end from spool. Do not allow wire to unravel. Be sure end of wire is straight and free of burrs. 6. Feed wire through wire feed guide tube, over the groove in drive roller and into gun liner. Flip tensioning screw up and adjust tension by rotating 4 Wire Feed Arc Welder Installation LOCATION Selecting the proper location can significantly increase performance, reliability and life of the arc welder. For best results locate welder in a clean and dry environment. Dus

41 Sp Corriente alterna o CA – corriente electrica que invierte periodicamente la direccion. La corriente de ciclo de sesenta viaja en ambas direcciones, sesenta veces por segundo. Longitud del arco - la distancia entre el extremo del electrodo y la punta donde el arco hace contacto con la superficie de trabajo. Metal de base – el material que va a ser soldado. Union plana – una union entre las dos partes alineadas aproximadamente en el mismo plano. Crater – charco de metal fundido o bolsillo qu

A protective coating called slag now covers the weld bead which prevents contaminants in the air from reacting with the molten metal. Once the weld cools to the point that it is no longer glowing red, the slag can be removed. Removal is done with a chipping hammer. Lightly tap the slag with the hammer and break it loose from the weld bead. The final clean-up is done with a wire brush. When making multiple weld passes, remove the slag before each pass. WELDING POSITIONS Four basic welding positio

EVERY 3 MONTHS: 1. Replace any unreadable safety labels on the welder. 2. Use compressed air to blow all dust and lint from ventilation openings. 3. Clean wire groove on drive roller. Remove drive roller and use a small wire brush to clean. Replace if worn or damaged. Supply Cable Replacement 1. Verify that welder is OFF and power cord disconnected. 2. Remove welder side panel to expose switches. 3. Disconnect the power cord leads per the diagram inside the unit. 4. Disconnect the ground wire co

This will blow out dust or dirt that may have accumulated around valve seat. 2. Install regulator onto cylinder valve. Tighten stem nut securely to gas valve. 3. Install one end of gas hose to fitting on the back of welder and other end of hose to fitting on regulator. Make sure gas hose is not kinked or twisted. 4. While standing opposite cylinder outlet, slowly open cylinder valve. Inspect for leaks in the connections. 5. Turn unit on and pull trigger on torch to allow gas to flow. Adjust gas

. Keep cylinders away from any welding or other electrical circuits. . Never allow a welding electrode to touch any cylinder. . Use only correct shielding gas cylinders, regulators, hoses and fittings designed for the specific application; maintain all parts properly. . Turn face away from valve outlet when opening cylinder valve. . Keep protective cap in place over valve except when cylinder is in use or connected for use. . Read and follow instructions on compressed gas cylinders, associated e