Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Campbell Hausfeld Dateigröße: 1.5 mb Dateiname: d010374a-e403-4ae4-8d60-7e994faab6cf.pdf Unterrichtssprache:

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Wire Feed TM Arc Welder BUILT TO LAST QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 Description The Campbell Hausfeld WF1800, WF1900 and WF2000 are 70 amp, single phase 115 volt input, wire feed arc welding machines. The WF2000 is equipped with infinite wire speed control to accurately select the proper wire feed rate needed for various welding conditions. Internal components are thermostatically protected. This welding system is designed for use with the Flux Core Arc Welding (FCAW) process. As delivered from the factory, this welder can weld with .030” (.8 mm) or .035” (.9 mm) diameter flux-cored wire. A starter spool of wire is included. UTILITYUTILITYWELDERWELDERWORK CLAMPWORK CLAMP OFFOFF LOWLOW DELIVERS SMOOTHDELIVERS SMOOTHDC POWERDC POWER HIGHHIGH WirWire Feede FeedWelderelder 115 VOL115 VOLT60HZ60HZFLUXCORE WirWire Feed We Feed WelderelderSoudeur Alimente en FilSoudeur Alimente en Fil Soladar con AlambrSoladar con Alambre Continuoe ContinuoFLUXCORE CHCH LOWLOW HIGHHIGH ON OFF 10 CAMPBELLHAUSFELDBUILT TO LASTSERIOUS DUTYSERIOUS DUTY Figure 1 - Welder Components and Controls WF1800 WF2000 1 2 3 4 1 2 3 4 5 6 POLARITY Welders are configured for DCEN, direct current electrode negative. DUTY CYCLE / THERMOSTATIC PROTECTION Welder duty cycle is the percentage of actual weld time that can occur in a ten minute interval. For example, at a 10% duty cycle, actual welding can occur for one minute, then the welder must cool for nine minutes. Internal components of this welder are protected from overheating with an automatic thermal switch. A yellow lamp is illuminated on the front panel (on/off switch) if the duty cycle is exceeded. Welding operations may continue when the yellow lamp is no longer illuminated. MIG CONVERSION The WF1800 and WF1900 are NOT convertible to MIG gas usage. Call 1-800746- 5641 to purchase conversion kit (WT600400AJ) for WF2000. Unpacking All welding accessories for the welder are inside the wire feed compartment. Lift and/or remove wire feed cover to find handle, workclamp, etc. When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings and screws, etc. are tightened before putting unit into service. Circuit Requirements This equipment ! CAUTION requires a dedicated 115 volt circuit. Refer to the following chart for the correct circuit breaker or fuse rating. Do not run other appliances, lights, or tools on this circuit while operating this equipment. Extension cords are not recommended. Blown fuses and tripped circuit breakers can result from failure to comply with this recommendation. Heat Circuit Breaker or Selector Slow Blow Fuse Low 15 amp High 20 amp See page 6 for supply cable replacement instructions. Components and Controls WF1800/WF1900 1. Work Clamp - connect to work piece. 2. Wire Feed Gun with .035” tip. 3. Power Cord - plug into 115 volt outlet. 4. Low/Off/High Switch - set according to metal thickness. Automatically controls wire speed. Lights if thermostat has automatically shut unit off. WF2000 1. Work Clamp - connect to work piece. 2. Wire Feed Gun with .035” tip. 3. Power Cord - plug into 115 volt outlet. 4. On/Off Switch - lights if thermostat has automatically shut unit off. 5. Infinite Wire Speed Control - turn clockwise to increase wire speed and counterclockwise to decrease wire speed. 6. Heat Selector - Selects welding power. Two selections are possible; low and high. For parts, product & service information © 2002 Campbell Hausfeld/Scott Fetzer IN199006AV 3/02 visit Operating Instructions and Parts Manual General Safety ! DANGER Danger means a hazard that will cause death or serious injury if the warning is ignored. Warning means a ! WARNING hazard that could cause death or serious injury if the warning is ignored. Caution means a ! CAUTION hazard that may cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property. NOTE: Note means any additional information pertaining to the product or its proper usage. ! WARNING Always keep a fire extinguisher accessible while performing arc welding operations. . Before starting or servicing any electric arc welder, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and/or serious personal injury or death. . All installation, maintenance, repair and operation of this equipment should be performed by qualified persons only in accordance with national, state, and local codes. ! WARNING Improper use of electric arc welders can cause electric shock, injury, and death! Take all precautions described in this manual to reduce the possibility of electric shock. . Verify that all components of the arc welder a...

Herunterladen

Geben Sie zwei Ziffern: