Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Campbell Hausfeld
Dateigröße: 1.22 mb
Dateiname: 1a33a53d-f8f5-489f-94e0-d0c6dc790495.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. BUILT TO LAST Wire Feed Arc Welder QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 Description This Campbell Hausfeld wire feed welder is designed to be used on standard 230 volt single phase current. The welder is equipped with an infinite wire speed control to accurately select the proper wire feed rate needed for various welding conditions. Internal components are thermostatically protected. This welder is designed for use with flux core arc welding (gasless) or gas metal arc welding (MIG) process. As delivered from the factory, this welder can weld with .030" (.8 mm) to .045” (1.2 mm) diameter wire. A starter spool of .035” (.9 mm) flux core wire and a .035” tip are included. Unpacking Some welder components may be found in the wire feed compartment. When unpacking, inspect carefully for any damage that may have occurred during transit. Report any damaged or CHCH FLUXFLUXCORECORE MIGMIG Power Cord (3) Polarity Hook-up (6) On/Off/Heat Selector Switch (4) Infinite Wire Speed Control (5) Work Wire Feed Gun (2) Clamp (1) Figure 1 MODEL WG4000 missing items by calling (800) 746-5641. Circuit Requirements This equipment ! CAUTION requires a dedicated 230 volt, minimum 20 amp circuit. Do not run other appliances, lights, or tools on this circuit while operating this equipment. Extension cords are not recommended. Blown fuses and tripped circuit breakers can result from failure to comply with this recommendation. Components and Controls 1. Work Clamp – Connects to work piece. 2. Wire Feed Gun with .035” tip 3. Power Cord – Plugs into 230 volt outlet. 4. On/Off/Heat Selector Switch – Turns welder on and off and selects welding power. Six (6) selections are possible. 5. Infinite Wire Speed Control – Controls wire speed (clockwise turn increases speed; counterclockwise turn decreases speed). 6. Polarity Hook-up (Inside Wire Feed Compartment) – Provides connections for MIG, direct current electrode positive (DCEP); and flux core, direct current electrode negative (DCEN). General Safety ! DANGER Danger means a hazard that will cause death or serious injury if the warning is ignored. Warning means a ! WARNING hazard that could cause death or serious injury if the warning is ignored. Caution means a ! CAUTION hazard that may cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property. NOTE: Note means any additional information pertaining to the product or its proper usage. Always ! WARNING keep a fire extinguisher accessible while performing arc welding operations. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. © 2003 Campbell Hausfeld / Scott Fetzer For parts, manuals, product & service information IN970800AV 3/03 visit or call (800) 746-5641. Wire Feed Arc Welder General Safety (Continued) . Before starting or servicing any electric arc welder, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and/or serious personal injury or death. . All installation, maintenance, repair and operation of this equipment should be performed by qualified persons only, in accordance with national, state, and local codes. Improper! WARNING use of electric arc welders can cause electric shock, injury, and death! Take all precautions described in this manual to reduce the possibility of electric shock. . Verify that all components of arc welder are clean and in good condition prior to operating the welder. Be sure that the insulation on all cables, wire feed gun, and power cords is not damaged. Always repair or replace damaged components before operating welder. Always keep welder panels, shields, etc. in place when operating the welder. . Always wear dry, protective clothing, welding gloves, and insulated footwear. . Always operate welder in a clean, dry, well ventilated area. Do not operate it in humid, wet, rainy, or poorly ventilated areas. . Be sure work piece is properly supported and grounded before beginning any electric arc welding operation. . Coiled welding cable should be spread out before use to avoid overheating and damage to insulation. ! DANGER Never immerse the wire or wire feed gun in water. If the welder becomes wet for any reason, be absolutely certain that it is completely clean and dry before using! . Always shut equipment off and unplug power prior to moving welder. Always attach work lead first. . Verify that work piece is securely grounded. . Always shut off electric arc welding equipment when not in use, and cut off any excess wire from wire feed gun. . Never allow any part of body to touch wire and ground or grounded work piece at the same time. . Awkward welding conditions ...