Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2 Breathing welding fumes can be hazardous to your health. 2.1 Keep your head out of the fumes. 2.2 Use forced ventilation or local exhaust to remove the fumes. 2.3 Use ventilating fan to remove fumes. 3 Welding sparks can cause explosion or fire. 3.1 Keep flammables away from welding. Don’t weld near flammables. 3.2 Welding sparks can cause fires. Have a fire extinguisher nearby and have a watch person ready to use it. 3.3 Do not weld on drums or any closed containers. 4 Arc rays can burn eyes and injure skin. 4.1 Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection. 5 Become trained and read the instructions before working on the machine or welding. 6 Do not remove or paint over (cover) the label. 2-2. Rating Label For CE Products S-178 813-A ISO/IEC 974-1 X 25% 60% 100% 7A/10.2V 310A/22.4V U0 = 80V I2 310A 200A 155A U2 22.4V 18V 16.2V X 25% 60% 100% 5A/20.2V 310A/32.4V U0 = 80V I2 310A 200A 155A U2 32.4V 28V 26.2V IP 21S U1 = 220 I1max = 117.2A I1Eff = 59A1 1 1 50 Hz U1 = 380 I1max = 72.2A I1Eff = 36A U1 = 415 I1max = 63.8A I1Eff = 32A OM-353 Page 10 2-3. Symbols And Definitions Some symbols are found only on CE products.NOTE A Amperes Panel–Local Gas Tungsten Arc Welding (GTAW) Shielded Metal Arc Welding (SMAW) V Volts Do Not Switch While Welding Arc Force (DIG) Spot Timer Output Circuit Breaker Remote Temperature Protective Earth (Ground) Alternating Current High Frequency Start Input Postflow Timer Preflow Timer High Frequency Continuous High Frequency Gas (Supply) Gas Input Gas Output Increase/Decrease Of Quantity On Off Percent Direct Current Balance Control Maximum Cleaning Maximum Penetration Electrode Positive Electrode Negative Crater Time Meter Single-Phase U0 Rated No Load Voltage (Average) U1 Primary Voltage U2 Conventional Load Voltage Line Connection I1 Primary Current I2 Rated Welding Current X Duty Cycle Single-Phase Combined AC/DC Power Source IP Degree Of Protection I1eff Maximum Effective Supply Current I1max Rated Maximum Supply Current Hz Hertz Electrode Work Thickness Gauge Spark Gap S Seconds OM-353 Page 11 SECTION 3 – INSTALLATION 3-1. Specifications Amperes Input at AC Balanced Rated Load Output, Rated Welding Output PFC** 50/60 Hz, Single-Phase KVA KW Amp Range Max OCV IP Rating200 V 230 V 460 V 575 V NEMA Class II No 106 92 46 37 21 11.4 (40) – 250 PFC (4.6*) (4*) (2*) (1.6*) (0.89*) (0.68*) Amperes, 30 Volts AC, 40% Duty Cycle 5–310 A 80 V 21 S With PFC 76 66 33 26 15.2 11.4 *While idling **Power Factor Correction Amperes Input at AC Balanced Rated Load Output, Rated RatedRated Welding Output PFC ** 50/60 Hz, Single-Phase KVA KW Amp Range Max OCV IP Rating200 V 220 V 230 V 260 V 380 V 415 V 460 V 520 V 575 V NEMA Class I (60) – 200 No PFC 85 (4.6*) 77 (4.2*) 74 (4*) 65 (3.5*) 45 (2.4*) 41 (2.2*) 37 (2*) 33 (1.8*) 30 (1.6*) 17 (0.9*) 8.3 (0.7*) Amperes, 28 Volts AC, 60% Duty Cycle 5–310 A 80 V 21 S With PFC 55 (57*) 64 (51*) 48 (49*) 48 (49*) 37 (30*) 34 (27*) 24 (25*) 48 (49*) 19 (20*) 11 (11*) 8.3 (0.6*) *While idling **Power Factor Correction 3-2. Volt-Ampere Curves The volt-ampere curves show the minimum and maximum voltage and amperage output capabilities of the welding power source. Curves of other settings fall between the curves shown. ssb1.1 10/91 – SB-116 199 / SB-116 200 A. DC Mode B. AC Mode OM-353 Page 12 OM-353 Page 13 3-3. Duty Cycle And Overheating 4 Minutes Welding 6 Minutes Resting 6 Minutes Welding 4 Minutes Resting Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, thermostat opens, output stops, light goes on (CE models only), and cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or duty cycle before welding. Exceeding duty cycle can damage unit and void warranty. 40% Duty Cycle At 250 Amperes (60 Hz Models Only) Overheating 0 15 A OR Minutes Reduce Duty Cycle duty1 4/95 / SB-116 198 60% Duty Cycle At 200 Amperes OM-353 Page 14 3-4. Selecting A Location 1 Lifting Eye 2 Lifting Forks Use lifting eye or lifting forks to move unit. If using lifting forks, extend forks beyond opposite side of unit. 3 Rating Label (Non CE Models Only) 4 Rating Label (CE Models Only, See Section 2-2) Use rating label to determine input power needs. CE label located on rear panel. 5 Plate Label (CE Models Only) 6 Line Disconnect Device Locate unit near correct input power supply. Special installation may be required where gasoline or volatile liquids are present – see NEC Article 511 or CEC Section 20. 1 2 Movement ST-800 402 / ST-117 264-F 6 18 in (460 mm) Location And Airflow OR 18 in (460 mm) 3 5 4 3-5. Dimensions And Weights Dimensions A Height 30-3/4 in (781 mm) B C Width 19-3/4 in (502 mm) E D Length 27-1/2 in (698 mm) A 27 in (686 mm) B 26 in (661 mm) F C 25-1/4 in (642 mm) Front D 1-1/2 in (38 mm) G E 1-1/8 (29 mm) F 17-7/8 (454 mm) G 19-1/4 (489 mm) H 1/2 in (13 mm) Dia H 6 Holes Weight ST-...