Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Campbell Hausfeld Dateigröße: 236.72 kb Dateiname: Unterrichtssprache:

These welders are equipped with infinite amperage control to accurately select the proper current needed for various welding conditions. Internal components are thermostatically protected. This welder can weld up to 1/8” steel in a single pass. Recommended electrode size is 1/16” diameter for 15 amp circuits, up to 5/64” diameter for 20 amp circuits. For replacement electrodes, call (800) 746-5641 for the nearest dealer. Unpacking When unpacking, inspect carefully for any damage that may have occurred during transit. Report any damaged or missing items by calling 1-800-746-5641. Circuit Requirements This equipment requires a dedicated 115 volt circuit. Refer to the following chart for the correct circuit breaker or fuse rating. Do not run other appliances, lights, or tools on this circuit while operating this equipment. Extension cords are not recommended. Blown fuses or tripped circuit breakers can result from failure to comply with this recommendation. Electrode Circuit Breaker or Diameter Slow Blow Fuse 1/16 15 amp 5/64 20 amp DECREASE INCREASE 1 2 3 4 5 6 1 2 4 5 6 3 1 Figure 1 -Welder Components and Controls MODEL WS0900 MODEL WS1020 ONLY Components and Controls 1. Work Clamp - connect to work piece 2. Electrode Holder - holds electrode welding rod 3. Power Cord - plug into 115 volt outlet. 4. On/Off Switch - lights if thermostat has automatically shut unit off. 5. Infinite Amperage Control Knob turns clockwise to increase amperage and counterclockwise to decrease amperage. 6. Welding Amp Indicator - as the amperage control knob (5) is rotated, the amperage indicator moves displaying approximate weld amps. General Safety Danger means a hazard that will cause death or serious injury if the warning is ignored. Warning means a hazard that could cause death or serious injury if the warning is ignored. Caution means a hazard that may cause minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property. NOTE: Note means any additional information pertaining to the product or its proper usage. IN198903AV 4/97 Shielded Metal Arc Welder Shielded Metal Arc Welder Always keep a fire extinguisher accessible while performing arc welding operations. . Before starting or servicing any electric arc welder, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and or serious personal injury or death. . All installation, maintenance, repair and operation of this equipment should be performed by qualified persons only in accordance with national, state, and local codes. Improper use of electric arc welders can cause electric shock, injury, and death! Take all precautions described in this manual to reduce the possibility of electric shock. . Verify that all components of the arc welder are clean and in good condition prior to operating the welder. Be sure that the insulation on all cables, electrode holders, and power cords is not damaged. Always repair or replace damaged components before operating the welder. Always keep welder panels, shields, etc. in place when operating the welder. . Always wear dry protective clothing and welding gloves, and insulated footwear. . Always operate the welder in a clean, dry, well ventilated area. Do not operate the welder in humid, wet, rainy, or poorly ventilated areas. . Be sure that the work piece is properly supported and grounded prior to beginning any electric arc welding operation. . Coiled welding cable should be spread out before use to avoid overheating and damage to insulation. Never immerse the electrode or electrode holder in water. If the welder becomes wet for any reason, be absolutely certain that it is completely clean and dry prior to attempting use! . Always shut the equipment off and unplug the power prior to moving the unit. . Always attach the work lead first. . Verify that the work piece is securely grounded. . Always shut off electric arc welding equipment when not in use and, and remove the electrode from the holder. . Never allow any part of the body to touch the electrode and ground or grounded work piece at the same time. . Awkward welding conditions and positions can be electrically hazardous. When crouching, kneeling or at elevations, be sure to insulate all conductive parts, wear appropriate protective clothing, and take precautions to prevent injury from falls. . Never attempt to use this equipment at current settings or duty cycles higher than those specified on the equipment labels. . Never use an electric arc welder to thaw frozen pipes. Flying sparks and hot metal can cause injury. As welds cool, slag can be thrown off. Take all precautions described in this manual to reduce the possibility of injury from flying sparks and hot metal. . Wear ANSI approved face shield or safety glasses with side shield protection when chipping or grinding metal parts. . Wear ear plugs when welding overhead to prevent spatter or slag from falling into ...

Herunterladen

Geben Sie zwei Ziffern: