Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Assembly and Operating Instructions For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. Cut-Off Tool SKU 95028 For technical questions, please call 1-800-444-3353 Page Assembly and Operation Instructions (continued) note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the Air Inlet (13) on the Air Cut-Off Tool. First, wrap the 1/4” air connector (not included) with pipe thread seal tape before threading into the Air Inlet (13). Connect a 3/8” I.D. Air Source Hose to the Cut-Off Tool. note: If you are not using an automatic oiler system, before operation add a few drops of Pneumatic Tool Oil to the airline connection. Add a few more drops after each hour of continual use. 2. Set the air pressure on your compressor to 90 PSI. Do not exceed the recommended air pressure of 90 PSI. 3. Check the air connection for leaks. 4. Disconnect the air hose until instructed to reconnect. 5. After disconnecting the air supply, squeeze the Trigger Lever (14) to make sure no air remains in the unit. Assembly: The only assembly required is the mounting of the Cutting Wheel (29). Warning: the Cut-Off Tool must be disconnected from the air supply when changing the Cutting Wheel (29). After disconnecting the air supply, squeeze the Trigger Lever (14) to make sure no air remains in the unit. 1. Place the Wrench (33) on the flats of the Spindle (25) to hold it in place. 2. Using the Allen Wrench (32), loosen and remove Hex Screw (31) and Spacer (30). 3. Remove and replace the Cutting Wheel (29). 4. Replace the Hex Screw (31) and the Spacer (30). Tighten the Hex Screw (31) while holding the Spindle (25) in place with the Wrench (33). See Figure 1. Cutting Wheel (29) Spacer (30) WARnInG: The Guard (27) Hex Screw (31) must be in place when using the Cut-Off Tool. Allen Wrench (32) Guard (27) Spindle (25) Figure 1 SKU 95028 For technical questions, please call 1-800-444-3353 Page Assembly and Operation Instructions (continued) WARnInG: Always check the Cutting Wheel (29) for possible wear. Do not use a worn, torn, or defective cutting wheel. WARnInG: Position the Cut-Off Tool so that the attached guard is in position between you and the workpiece to protect you from flying debris. WARnInG: The Guard (27) must always be attached to the Cut-Off Tool. 1. Check the Cutting Wheel (29) for wear, Replace if necessary. 2. Set the compressor to 90 PSI. Do not exceed 90 PSI. 3. Connect the Cut-Off Tool to the air hose as explained on Page 5 of this manual. 4. Use both hands to grip the Cut-Off Tool. Gently squeeze down on the Trigger Lever (14). Allow the Cut-Off Tool to run for a few seconds before approaching the workpiece. 5. Let the Cut-Off Tool do the work. Do not apply force on the workpiece. 6. When finished, release the Trigger Lever (14). 7. Disconnect the Air Hose. 8. Gently squeeze down on the Trigger Lever (14) to release any air that might still remain in the Cut-Off Tool. Inspection, Maintenance, and Cleaning 1. Warning: Always release any excess air, make sure the Trigger Lever (14) is in its “OFF” position, and disconnect the Cut-Off Tool from its compressed air supply before performing any inspection, adjustments, maintenance, or cleaning. 2. Before each use, inspect the general condition of the Cut-Off Tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hose, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. never use damaged equipment. 3. After each use, wipe down the Cut-Off Tool with a clean cloth, remove all dirt, oil, and grease from the Cut-Off Tool. If necessary, you may use a mild detergent. Do not use solvents, as damage to the Cut-Off Tool may occur. Do not immerse the Cut-Off Tool in any liquids. SKU 95028 For technical questions, please call 1-800-444-3353 Page Parts List and diagram Part description Q’ty 1 Plug Screw 1 2 O-Ring 1 3 O-Ring 1 4 Air Regulator 1 5 Valve Spring 1 6 O-Ring 1 7 Valve Stem 1 8 O-Ring 1 9 Motor Housing 1 10 Valve Bushing 1 11 O-Ring 2 12 Muffler 1 13 Air Inlet 1 14 Trigger Lever 1 15 Lever Pin 1 16 Bearing 1 17 Bearing Plate 1 18 Ball 2 Part description Q’ty 19 Rotor Blade 4 20 Rotor 1 21 Cylinder 1 22 Bearing Plate 1 23 Bearing 1 24 Washer 1 25 Spindle 1 26 Lock Ring 1 27 Guard 1 28 Nut 1 29 Cutting Wheel 1 30 Spacer 1 31 Hex Screw 1 32 Allen Wrench 1 33 Wrench 1 nOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 95028 For technical questions, please call 1-800-444-3353 Page 90 day Warranty 90 day Warranty Harbor ...