Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When the blade is replaced with a new one, check the flange washers and the drive axle. See instructions under the heading Checking the drive axle and flange washers. Checking the drive axle and flange washers Check that the threads on the drive shaft are undamaged. Check that the contact surfaces on the blade and the flange washers are undamaged, of the correct dimension, clean, and that they run properly on the drive axle. Do not use warped, notched, indented or dirty flange washers. Do not use different dimensions of flange washers. Guard for the blade The guard must always be fitted on the machine. The guard for the cutting equipment should be adjusted so that the rear section is flush with the work piece. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user. Starting and stopping WARNING! Note the following before starting: The machine should be connected to an earthed outlet socket. Check that the mains voltage corresponds with that stated on the rating plate on the machine. Make sure you have a secure footing and that the cutting blade cannot touch anything. Keep people and animals well away from the working area. Before starting (K3000 Wet) Water connector Connect the water hose to the water supply (A). The water flow is regulated using the water tap (B). Ground fault circuit interrupter Make sure the ground fault circuit interrupter is switched on. The LED indicates that the ground fault circuit interrupter is on and that the machine can be switched on. If the LED is not on, push the RESET button (green). Check the ground fault circuit interrupter. See instructions under the heading Checking, maintaining and servicing the machine’s safety equipment. Starting •Grip the front handle with the left hand. •Grip the rear handle with your right hand. •Press in the power switch lock with your right-hand thumb and press in the power switch. •Run the machine unloaded and in a safe manner for at least 30 seconds. Stopping WARNING! The cutting blade continues to rotate for some time after the motor has stopped. Stop the motor by releasing the power switch. Maintenance WARNING! Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected. Cooling system The machine is equipped with an efficient fan to cool the motor. Cooling air which is drawn in through the grille by the machines rear handle passes over the stator and rotor and out through the front of the motor housing. In order for the machine to always be cooled sufficiently the cooling air openings must be kept clear and clean. Blow down the machine regularly with compressed air. Electrical Feed WARNING! Never use damaged cables. They can cause serious, even fatal, personal injuries. Check that the cord and extension cord are intact and in good condition. Never use the machine if the cord is damaged, hand it in to an authorized service workshop for repair. Replacing the carbon brushes Check the carbon brushes at least once a month. The carbon brushes should be replaced with new brushes if they are worn, cracked or in any other way deformed. All carbon brushes must be replaced when the brushes are replaced. •Remove both inspection covers by loosening both screws. •Unscrew the cable holding the carbon brush. Now lift up the spring and then lift out the carbon brush from the brush retainer. •Clean the brush retainers with a dry brush. •Carefully blow away the dust. •Fit the new carbon brushes and, at the same time, check that they slide easily in the brush retainers. •Fold down the springs and tighten the cable. •New carbon brushes must be run in for approximately 40 minutes while idling. Bevel gear The grease in the gear housing should be changed every 4 months. Use high quality gear grease The gear housing must not be filled completely with grease. The grease expands as the machine heats up during operation. If the gear housing was completely filled with grease it could damage the seals and lead to leakage of grease. The gear housing should contain 90 g of grease in total. Changing the grease The following parts must be dismantled to change the grease in the gear housing: 1Flange washers holding the cutting blade 2The sealing ring 3Support flange for the guard 4Guard for the blade 5The four screws holding the shield. Lift the shield together with the drive wheel unit out of the gear housing. 6Wipe out the grease and fill with new, good quality gear grease. The gear housing should contain 90 g of grease in total. CAUTION! Exercise care when dismantling so as not to damage the gaskets. These are used both as seals and spacers for the gear setting. Checking the drive axle and flange washers Check that the threads on the drive shaft are undamaged. Check that the contact surfaces on the blade and the flange washers are undamaged, of the correct dimension, clean, and that they run properly on the drive axle. Do not use warped, notched, indented or dirty flange was...
Dieses Handbuch ist für folgende Modelle:Schweißtechnik System - K3000 Wet (719.88 kb)