26.The final part of a tumble dryer cycle occurs without heaat(cool down cycle)to ensure that the items are left at a temperature that ensures that the items will not be damaged. WARNING:Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. 3 4 5 Dimensions a = 855 mm b = 620 mm c = 595 mm Weight = 43 kg Packing accessories Checklist of the accessories and materials provided with the machine: Quantity To e

"Sensor Dryness Level" is inactive, pressing of which will get alarms. 7. Press "Start/Pause" button. 19 Francais RACK DRY CYCLE 1. Press any button except "Off" button to power on. 2. Press "Timed-Dry Cycles" button and select "Rack Dry" cycle. • After powering on, press "Timed-Dry Cycle" button to select "Rack Dry" program. 3. Press "More Time" And "Less Time" buttons to set a suitable time. • After setting "Timed-Dry Cycle" to "Rack Dry", you can press these two buttons to increase or decreas

The appropriate load should be 1/3" to 1/2" of the drum volume. • Balance the dryer load evenly throughout the dryer for the best result. • Drying time depends on many variables: load size, type of fabric and moisture in it, heat and moisture in the room, electric voltage, length of the exhaust duct, etc. • To eliminate guessing and to conserve energy,it is recommend for certain clothes to dry on an auto-drying setting. • Always follow the fabric care instructions supplied by the garment man

0 Setting the programme. 0 Hold down the DELAY TIMER (STARTTIJDKEUZE) button until the required number of hours before the programme is to start is shown in the display panel. 0 Press START/PAUSE (START/PAUZE ) button. After the set number of hours has passed the tumble dryer will automatically begin the set drying programme. The number of hours until the set drying programme is due to begin is shown in the display panel. You can adjust the pre-selected delay start at any time. Drying Start the

The weight should not exceed 10 lbs (4.5 kg). Select the air (no heat) setting for items containing plastic, foam rubber, rubber-like materials, feathers or down. When items are dry, remove the rack and store it in a convenient location. Care and Cleaning • Before cleaning the dryer interior, unplug the electrical power cord to avoid electrical shock hazards. • Do not use any type spray cleanser when cleaning the dryer interior. Hazardous fumes or electrical shock could occur. INSIDE • Clean the

Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. WARNING ELECTRICAL SHOCK HAZARD A U.L.-approved strain relief must be installed onto • power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. Do not use an aluminum wired receptacle with a• copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and alu

5. Damages to finish after installation. 6. Replacement of light bulbs and/or fluorescent tubes (on models with these features). This warranty does not cover the following: EXCLUSIONS 1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. 2. Servic

Contact a qualifi ed technician immediately. Normal Operating Sounds A B C D You may or may not hear the following sounds from your new dryer: A. SUSPENSION ROLLERS The dryer drum is supported by a set of suspension rollers. At times there may be a thumping or rolling sound when the dryer starts. This may happen if the dryer has not been in use for a period of time, or after a heavy load has remained in the dryer drum for an extended period, creating a temporary fl at spot on the edge of the rol

The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation. ..NOTE Use of 90° quick-turn elbow required to meet minimum installation depth of free-standing dryer: • Straight back venting allows for 0” (0 cm) installation. • Venting right with 90° elbow allows for 0.75” (2 cm) installation. • Venting downward with 90° elbow allows for 0.75” (2 cm) installation. • Venting left with short, straight adapter and 90° elbow allows for 3.75” (9.5 cm