Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
tion). Fine strainer not in place Install fine strainer and/or Loading door does not and/or large mesh filter not snap large mesh filter into close. locked in place. place. Problem Possible cause Remedy When pressing a but- Washing protection. After ton, the corresponding the start of the programme, Turn the programme knob to button flashes several the option can no longer be OFF. Set the programme again. times. set. Programme selector in OFF Turn programme selector to position. LIGHT or to any programme. Drum light does not work. Replace lamp (see next sec- Defective lamp. tion). Programme inactive, Empty condensate tank, then EMPTY WATER display Condensate tank is full. start programme with START/ illuminated. PAUSE button. Drying cycle ends Select time programme or Not enough washing load- shortly after pro- higher drying level (e.g. INTEN ed or washing loaded is too gramme starts. END SIVE DRY instead of STORAGE dry for selected programme. display illuminated. DRY). Drying cycle lasts an unusually long time. Note: After up to 5 hours the drying cycle finishes automatically (see ”Drying cycle complete”). Lint filter clogged. Clean lint filter. Heat exchanger clogged Clean heat exchanger. with lint. SPECIAL CARE button SPECIAL CARE is only suitable pressed and load volume too for use with loads of up to big. 3kg! Load volume too big. Reduce load volume. Laundry insufficiently pre- Laundry must be adequately drained. pre-drained. Changing bulb for inside light Only use a special bulb which is designed specially for dryers. The special bulb is available from the after-sales service, ET-Nr. 112 552 000-5. 1 Warning! Do not use standard bulbs! These develop too much heat and may damage the machine! 1 Warning! Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. 1.Unscrew covering bonnet from above bulb (this can be found directly behind the loading aperture, at the top; refer to “Description of machine” section.) 2.Replace defective bulb. 3.Screw covering bonnet back down. 1 Warning! For reasons associated with safety, the covering bonnet must be screwed down tightly. If this is not done, the dryer must not be operated. Programming options Objective Implementation Permanently program in the audible signal which reminds you that the programme is complete. Adjust detection of degree of drying: If the laundry is slightly drier or slightly damper at the end of the programme than with the standard setting. If the EMPTY WATER display is to remain permanently deactivated when using an external condensate drain. 1. Turn the programme selector to any programme. 2. Press the AUDIBLE SIGNAL button and hold down for approx. 5 seconds. A brief signal sounds several times. The AUDIBLE SIGNAL display flashes several times. The setting is permanently programmed. The setting is cancelled as described under 1 and 2. 1. Turn the programme selector to any programme. 2. Press the SENSITIVE and START/PAUSE buttons at the same time and hold down for approx. 5 seconds. The current setting is displayed on the programme progress display: – END display: Setting for drier laundry – COOLING display: Standard setting – DRYING display: Setting for damper laundry 3. Press the START/PAUSE button until the setting required appears on the programme progress display. 4. Turn the programme selector to OFF. The setting is permanently programmed. 1. Turn the programme selector to any programme. 2. Press the SPECIAL CARE and AUDIBLE SIGNAL buttons at the same time and hold down for approx. 5 seconds. The EMPTY WATER display flashes briefly. The EMPTY WATER display is permanently deactivated. Settings may be cancelled as under 1 and 2, but the EMPTY WATER display is briefly illuminated (instead of flashing). Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x width x depth 85 x 60 x 60 cm Depth with loading door open 109 cm Height can be adjusted by 1.5 cm Weight when empty approx. 40kg Loading volume (depends on programme) 1) max. 6kg Energy consumption in accordance with IEC 1121 s. e. 4.3kWh (6kg of cotton, pre-drained at 800 rpm, COTTONS STORAGE DRY programme) Scope Domestic permissible ambient temperature + 5°C to + 35°C 1) Different loading volume data may be needed in some countries as a result of different measuring methods. Consumption values The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances. Programme Loading volume in kg Energy consumption in kWh COTTONS STORAGE DRY 1) 6 4.3 COTTONS HAND IRON 1) 6 3.5 EASY CARES STORAGE DRY 2) 3 1.6 1) pre-drained at 800 rpm 2) pre-drained at 1000 rpm Installation and connection instructions 1 Installation safety instructions • Bef...