Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3 Lower Front Panel Removal ............................................................. 3 Upper Front Panel Removal ............................................................. 3 Top Cover Removal ......................................................................... 3 Lint Box/Blower Assembly Removal ................................................. 4 Gas Valve/Ignition System Removal ................................................. 5 Oven Chamber Removal .................................................................. 5 Gas Valve/Ignition System Components........................................... 6 Oven Housing Components ............................................................. 6 Tumbler Support Wheel Assembly Replacement .............................. 6 Tumbler Alignment ........................................................................... 7 Belt Replacement ............................................................................ 6 Placing the Belt Back on the Motor Sheave...................................... 9 Electrical Component Locations ............................... 10 Electrical Panel.............................................................................. 10 Fire Suppression System Items, Terminal Block, and Axial Temperature Probe ......................................................... 11 Sail Switch Assembly..................................................................... 11 Exhaust Probe, Exhaust Hi-Limit, and Lint Drawer Switch .............. 11 Oven Contactor.............................................................................. 11 We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models. The illustrations included in this manual may not depict your particular dryer exactly. Part Locations and Removal LOWER FRONT PANEL REMOVAL: TOP COVER REMOVAL: Remove the lint drawer. Remove the four screws First remove the back guard, then pull top cover located just below the loading door. Tilt the top of toward the rear of the dryer and lift up. the panel out and lift the panel up and away from the dryer. UPPER FRONT PANEL REMOVAL: Remove the four screws located just above the loading door. Tilt the bottom of the panel out and lift the panel up and away from the dryer. 450262-1 LINT BOX/BLOWER ASSEMBLY REMOVAL: Remove screws and nuts at the rear of the lint box. Unplug wires from the capacitor. To remove motorized impellor assembly, remove the five screws and four nuts, shown with arrows. Remove cover and pull the motorized impellor assembly out through the opening. Remove two screws just above the lint drawer and pull the lint box down from the front and out slightly. Unplug three connections at the left of the lint box. The lint box may now be pulled out through the front of the dryer. American Dryer Corp. 450262-1 GAS VALVE/IGNITION SYSTEM REMOVAL: Be sure to shut off the gas main and then proceed to remove electrical connections and screws indicated. Remove lower front panel. Disconnect union and screws noted with arrows. The gas valve and burner orifice can now be carefully pulled toward the front of the dryer. Be sure to pull the assembly straight back so as not to strike the very fragile carbon ignitor. With the assembly partly out of the oven, the ignitor and the two gas valve electrical connections can be disconnected. At this point the assembly can be removed from the dryer. Replace assembly in the reverse order but make sure the tab at the rear of the assembly engages into the oven base slot. Inspect all wires to be sure all lead directly toward the front of the dryer. Be sure no wires are caught on the burner tube or ignitor. OVEN CHAMBER REMOVAL: The oven chamber can be removed after the gas valve/ignition system has been removed. Remove the two screws indicated by the arrows. Pull the oven housing part way out through the front and disconnect all wire connections. The oven housing can now be removed. Replace assembly by leading the housing cone into the hole in the rear wall. Replace screws and wire connections. 450262-1 GAS VALVE/IGNITION SYSTEM COMPONENTS BURNER TUBE IGNITOR GAS VALVE OVEN HOUSING COMPONENTS HEAT SENSOR OVEN CHAMBER BURNER HIGH-LIMIT TUMBLER SUPPORT WHEEL ASSEMBLY REPLACEMENT: The front wheel assemblies can be replaced with the lower front panel removed. Remove the three bolts by reaching upward with a socket or box wrench. The illustration below is provided to show the location of these wheels as the wheels cannot easily be seen while standing in front of the dryer. The left rear wheel assembly can be removed with just the back guard removed. The rear right wheel requires removing the back guard, heat duct, and oven. Be sure to mark the position of rear wheel brackets prior to removal (refer t...