Stimmen - 6, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
It is extremely important that the dryer is installed in a well ventilated location. This dryer must exhaust air outdoors. Do not install the dryer in any room or closet which does not permit the free flow of replacement air. Before installing the dryer ensure that there is sufficient height to fully open the lid. Allow sufficient room behind the dryer for the exhaust. The air intake is at the rear of the dryer. Ensure that there is a sufficient air passage on each side of the dryer for intake air. The area in which the dryer is located must be kept clear and free from combustible materials, gasoline and other flammable vapours and liquids. A dryer produces combustible lint so the area around the dryer must be cleaned regularly to keep it free of lint. This dryer can only be vented from the rear and must be exhausted to the outdoors. Alcove or closet installation WARNING When installing a dryer in a closet/alcove it must be exhausted to the outdoors. No other fuel burning appliance can be installed in the same closet or alcove. The top opening area in the door must be a minimum of 48 square inches (310cm2) and the bottom opening area must have a minimum of 24 square inches (155cm2). These openings must never be obstructed (a louvred door with the minimum air opening is acceptable). Minimum installation clearances are required but more clearance is recommended. 1" (25mm) 1" (25mm) 1" (25mm) min 2" (50mm) min 3" (76mm) min 56" (1372 – 1422mm) total ventation area 72 sq" (465cm2) 24 sq" (155cm2) 48 sq" (310cm2) Dimensions Lid clearance Check that there is enough clearance for the lid to fully open. .............................................................................................................................. .......................................................... Exhaust outlet location 13 7/8" (352mm) 13 1/8" (333mm) Exhaust outlet 4 3 / 8 " ( 111mm) Mobile home installation The installation of the dryer in a mobile home must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 HUD (Part 280), 1975} for the United States. When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made. A Mobile Home Installation kit is available with instructions (see Accessories page 4). Locate in an area that has adequate make up air (a minimum of 72 square inches of unobstructed opening is required). Mobile home installations must be exhausted to the outdoors with the exhaust duct termination securely fastened to the mobile home structure, using materials that will not support combustion. The exhaust duct must not terminate beneath the mobile home. See the section on exhausting for more information. .............................................................................................. ............. ..... ............. ....... ....... ... ............... ............... ... . ............................. ............. ... ..... ........... ....... ................. ..... ....... ..... ................. ............. ..... ........... ......... ............... Exhausting The dryer must be exhausted to the outdoors. This will prevent the build up of lint and moisture in the room in which it is located and reduce the risk of fire. WARNING Fire Hazard The dryer must be vented to the outdoors. Use rigid or thick wall flexible metal exhaust duct. Do not use a plastic exhaust duct. Do not use a metal foil exhaust duct. Failure to follow these instructions can result in death or fire. This appliance must always be vented to the outdoors. Exhaust ducting products can be purchased from your local Appliance store or Hardware store. Plastic or metal foil flexible duct can kink, sag, be punctured, reduce airflow, extend drying times and affect dryer operation. A minimum of 4 inch (100mm) thick wall flexible metal or rigid galvanised metal duct must be used. Using ducts larger than 4 inches (100mm) diameter may result in more lint accumulating. Using straight rigid metal ducting will minimise lint accumulation. Thick wall flexible metal ducting may be used but care must be exercised to avoid sharp bends which may squash the duct & cause blockages. Do not use plastic ducting or thin wall flexible metal ducting. Use duct tape to secure joints. Do not use screws as they collect lint. Keep ducting as short and straight as possible. Do not exceed the maximum exhaust duct lengths stated later in these installation instructions. Do not exhaust the dryer into a chimney or gas vent, a wall, a ceiling or any concealed space in a building. Do not exhaust the dryer under a house or mobile home or a porch, or into a window well or other area that will accumulate lint. The exhaust duct should end with an exhaust hood with a swing out damper to prevent back drafts and entry of wild life. Never use exhaust hoods with a magnetic damper. The hood should have at least 12 inc...