Login:
Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Anleitung GE, modell DPVH8800GJ

Hersteller: GE
Dateigröße: 431.62 kb
Dateiname: 492ce2da-afa8-4f04-a502-492a2a60baa5.pdf
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


• Completion time – 1 to 2 hours • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. CAUTION — Due to the size and weight of these products, and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION. • See washer and dryer installation instructions for additional installation requirements and guidelines. 2 Installation Instructions INSTALL THE PEDESTAL TO THE WASHER OR DRYER Place the pedestal against the bottom of the unit. Check to be sure the drawer front is at the front of the unit. Align the holes in the pedestal with the holes in the bottom of the unit. Use a Phillips screwdriver to install the 4 screws through the pedestal and into the unit—do not tighten. Slide the pedestal toward the unit, until it is aligned front to back. Use an 8 mm socket wrench to securely tighten the screws. C B A PREPARE THE PEDESTAL 3 Pull the drawer out as far as it will go. Remove screws from drawer slides. Slide drawer out of the base and set aside. FOR DRYERS ONLY: Locate the 4 support pads from the parts package. Each pad has 2 protrusions that fit into the holes on top of the pedestal. Press the rubber pads into each set of corner holes on the top of the pedestal as shown. NOTE: The support pads should be installed on the dryer only. DO NOT INSTALL THESE PADS ON THE WASHER PEDESTAL. C B A 2 Installation Instructions LEVEL THE WASHER OR DRYER Locate the 4 legs from the parts package and install. Stand the washer or dryer upright. Move it close to its final location. Make sure that the washer or dryer is level by placing a spirit level on top. Check side to side and front to back. Use an open ended wrench to adjust the legs in and out. Tighten the lock nut against the bottom of the pedestal. NOTE: • To minimize vibration, the locking nuts must be tight. • To reduce vibration, ensure that all four rubber leveling legs are firmly touching the floor. Push and pull on the back right and then the back left of your washer or dryer. D C B A 4 REINSTALL THE DRAWER Check to be sure the slides are closed. Slide the drawer into the opening. Align the drawer supports to the slides on each side. Reinstall the original screws into each drawer slide. Tighten both screws. Open the drawer fully. Slide drawer divider into slots in the center of the drawer. The drawer should slide smoothly when you push it closed. D C B A 5 Drawer divider REMOVE SHIPPING SCREWS Remove the 4 shipping screws on the back side of the unit. 6 FINALIZE THE INSTALLATION Refer to the washer or dryer Installation Instructions to complete the installation. 7 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE 3 Instructions d’installation CONTENU DE LA TROUSSE 4 coussinets de support 4 vis de montage Separateur de tiroir AVANT DE COMMENCER Lisez attentivement et en entier toutes ces instructions. • IMPORTANT — Conservez ces instructions a utiliser par l’inspec...

Dieses Handbuch ist für folgende Modelle:
Trockner - SPSD157JMG (431.62 kb)
Trockner - SPSD157JMV (431.62 kb)
Trockner - SPSD157JWW (431.62 kb)
Trockner - WPDH8800 (431.62 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien